Iteaduino-BT is an Arduino compatible board with a master/slave Bluetooth Module HC-05. It based on Arduino Duemilanove, 100% compatible to its existing program, shield and IDE. On the hardware part, remarkable changes are taken to improve the flexibility and user experience.
Wifi Bee is a xBee Pro socket compatible module.It integrates Microchip IEEE 802.11 Wi-Fi transceiver module MRF24WB0MA and 8bit AVR MCU ATmega328P. The smart and similar xBee Pro outlook makes it very easy to be integrated in your product. The ATmega328P could be directly programmed under the open source IDE Arduino when you plug it on to the UartSBee....
Foca is a FT232RL breakout. The FT232RL is a USB to serial UART interface with optional clock generator output. It’s the essential tools for establishing communication between PC and mostly MCU. Especially, it’s the optimum tool for basic boards without without USB interface, like arduino pro, colorduino, etc.
The good point is that it also...
BTBee is an easy to use Bluetooth SPP module compatible with existing Xbee sockets, designed for transparent wireless serial connection setup. It can directly plug into the Bee sockets and use the UART port for Bluetooth communication.
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+.This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401+ and add some extra pipelines, buffers, and an auto-retransmit feature.
This is a long distance 2.4G wireless module which basic on nRF24L01+ chip, and there is the PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.
The Bluetooth Shield integrates a HC-05 Serial Bluetooth module. It can be easily used with Arduino for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port).
It is proximity ID card of 125KHz, EM4100. It has been specially manufactured and packaged to be clean from dust. And you can print any pictures on the PVC blank cards. You can use it with our RDM6300 RFID reader module.
RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can...
This GSM module is a breakout board and minimum system of SIM900 Quad-band GSM/GPRS module. It can communicate with controllers via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). This module support software power on, reset, data transfer and audio.
A wireless relay is a codec-adaptive RF receiver with single channel relay. It helps easily deployment of wireless AC control for electrical appliances.Max 30 difference codec, unlimited controller or transmitter of each codec. Adaption of most popular RF remote controller, except rolling code.
The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Arduino.
Wireless Sensor Node - Solar Kit is an easy to use bundle created for experimenting with XBee and XBee compatible standalone wireless modules like RFBee and Wifi Bee. Every maker is confronted with the question of selection the right set of components to build Wireless Sensor Node. Wireless Sensor Node - Solar Kit fills this place very appropriately.
This kit is used for one way wireless communication at a frequency of 433MHz and includes a transmitter module and a receiver module. The twig configuration of this kit allows for around 40 meters of transmitting distance indoors, or around 100 meters outside.