Wireless Connectivity

 2
Out of stock
Dev. Tools

iTead 3G shield for Arduino (Arduino Compatible)

iTeadStudio
ASHITE3G
€62.50
The 3G shield is based on SIM5216E module. The SIM5216 series is Multi-Band HSDPA/WCDMA/GSM/GPRS/EDGE module solution which supports HSDPA up to 3.6Mbps for downlink data transfer. The 3G shield can be used for 3G communication, it is controlled via AT commands and fully compatible with Arduino.
 2
Out of stock
Dev. Tools

LoNet - Mini GSM/GPRS/GPS Breakout

GSMGPSLONET
€60.00
LoNet is a GSM and GPS two-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation. It features ultra-low power consumption in sleep mode and integrated with charging circuit for Li-Ion batteries, that make it get a super long standby time...
 2
Out of stock
Arduino

iTead WiFi shield for Arduino (Arduino Compatible)

iTeadStudio
ASHITEWIFI
€50.00
This Wifi Shield utilizes a RN171 wifi module to provide your Arduino/Iteaduino with serial Ethernet's function. It only takes two pins to hook your device up to 802.11b/g wireless networks with this shield.
 2
Available
Arduino

Seeed Studio WiFi shield for Arduino (Arduino...

iTeadStudio
ASHSESWLS06201P
€45.00
This Wifi Shield utilizes a RN171 wifi module to provide your Arduino/Seeeduino with serial Ethernet's function. It only takes two pins to hook your device up to 802.11b/g wireless networks with this shield. It features an independent antenna which can cover a wider range and transmit stronger signals. With supports for common TCP, UDP and FTP...
 2
Out of stock
Dev. Tools

iComSat SIM900 GSM/GPRS shield for Arduino...

ASHITEICOMSAT
€44.95
The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Arduino.
 2
Out of stock
Dev. Tools

SIM900 GSM/GPRS Module

GSMSIM900
€37.50
This GSM module is a breakout board and minimum system of SIM900 Quad-band GSM/GPRS module. It can communicate with controllers via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). This module support software power on, reset, data transfer and audio.
 2
Available
Electronics

RN-XV Wifly XBee (RN-171 XV, Wire antenna)

WIRRN171XV
€35.00
RN-XV XBEE The RN-171-XV is a 802.11 b/g solution especially designed for designers who want to migrate their existing 802.15.4 architecture to a more standard TCP/IP-based platform without redesigning their existing hardware. Based on a pseudo standard footprint often found in embedded applications, the Roving Networks’ RN-171-XV module provides Wi-Fi...
Out of stock
Tools

GO2NFC141U USB NFC Reader

NFCGO2Reader
€33.17
The GO2NFC141U NFC Reader is contactless smart card reader/writer developed based on the 13.56 MHz Contactless (RFID) Technology. Unlike other NFC readers/writers, GO2NFC141U is very compact and small.
 2
  • Reduced price / -€1.67
Available
Dev. Tools

Iteaduino BT HC-05 (Arduino-compatible with...

iTeadStudio
MCB00001
€30.00 €31.67
Iteaduino-BT is an Arduino compatible board with a master/slave Bluetooth Module HC-05. It based on Arduino Duemilanove, 100% compatible to its existing program, shield and IDE. On the hardware part, remarkable changes are taken to improve the flexibility and user experience.
Out of stock
Dev. Tools

M24SR-DISCOVERY (Discovery kit for the M24SR...

ST Microelectronics
MCBM24SRDISCO
€30.00
The M24SR-DISCOVERY is a demonstration kit to evaluate the features and capabilities of the M24SR series and is based on the M24SR64 device. The M24SR64 device is a dynamic NFC/RFID tag IC with a dual interface. It embeds a 64 Kbits EEPROM memory. It can be operated from an I2C interface or by a 13.56 MHz RFID reader or an NFC phone. The I2C interface...
 2
Available
Home

CC2541 SensorTag Development Kit

Texas Instruments
SENTICC2541SENSORTAG
€29.26
The CC2541 SensorTag is the first Bluetooth Smart development kit focused on wireless sensor applications and it is the only development kit targeted for smart phone app developers. The SensorTag can be used as reference design and development platform for a variety of smart phone accessories.
 2
  • Reduced price / -€10.00
Out of stock
Dev. Tools

Blend Micro - an Arduino-Compatible Development...

Arduino
BLENDMICRO
€25.00 €35.00
Blend Micro is Red Bear's first integrated developement board, we have "blend"ed Arduino with Bluetooth 4.0 Low Energy (aka BLE or Bluetooth Smart) into a single board. It is targeted for makers to develop low power Internet-Of-Things (IoT) projects quickly and easily.   The micro-controller unit (MCU) is Atmel ATmega32u4 and the BLE chip is Nordic...
 2
Out of stock
Dev. Tools

DevDuino Sensor Node V3 (ATmega 328)

MCBDDUSNODV3
€24.92
devDuino Sensor Node V3 is a compact Arduino-compatible microcontroller and is designed to build wireless networks based on transceiver nRF24L01+. You can easily connect other sensors or actuators to this platform, to build your remote monitoring or controlling system
 2
Out of stock
Dev. Tools

BT (Bluetooth) BLE Shield for Arduino

iTeadStudio
ASHITEBTBLE
€24.50
BLE shield is to adapt Bluetooth Low Energy to serial port, which is specifically designed for Arduino motherboard and compatible boards, plug and play.
 2
Available
Wireless Connectivity

Smart Socket WiFi Orvibo S20 (EU Plug)

RELORVS20EU
€22.50
Instantly convert any plug into a connected and intelligent outlet with a convenient timer function that works both on your smart phone and has a manual control knob. Perfect for lighting and other appliance with pre-set ON/Off functions. Control devices from anywhere
 2
Available
Sound

Bluetooth audio receiver and amplifier...

AUDBTTDA7379
€21.67
50w This bluetooth audio receiver comes bundled with a big 50W amplifier, making it ready to receive your audio streams wirelessly on any speaker.
 2
Available
Dev. Tools

SIM800L GSM/GPRS Module

WIRELESIM800L
€20.00
This module power supply of 5V, computer debugging USB to TTL serial port. 800MA power supply output current , TTL serial port compatible with 3.3V and 5V MCU, the MCU can be connected directly. IPX antenna interface can switch PCB antenna, glue stick antenna and sucker antenna. SIM800L 4 frequency data communications, globally available.
 2
Available
Home

BTBee Pro

iTeadStudio
WIRITEBTBEEPRO
€19.38
BTBee Pro is a serial port Bluetooth module which can be compatible with the shields which with XBee sockets. It's designed for Bluetooth wireless transfer. It supports Slave and Master mode, can be plugged into XBee socket and using the UART for transparent transmission. This module supports Bluetooth Wireless Program as well.
 2
Out of stock
Dev. Tools

BTBee (Bluetooth Bee, serial tu bluetooth module)

iTeadStudio
WIRITEBTBEE
€18.38
BTBee is an easy to use Bluetooth SPP module compatible with existing Xbee sockets, designed for transparent wireless serial connection setup. It can directly plug into the Bee sockets and use the UART port for Bluetooth communication.
 2
Available
Home

Wio Link (ESP8266, Grove and Battery charging...

MCBWIOLINK
€17.50
Wio Link is designed to simplify your IoT development. It is an ESP8266 based open-source Wi-Fi development board to create IoT applications by virtualizing plug-n-play modules to RESTful APIs with mobile APPs. The traditional methodology of building IoT applications consists of electronic engineering, micro-controller programming, network programming,...
 2
Out of stock
Dev. Tools

DevDuino Sensor Node V2 (ATmega 328, AAA...

Seeed Studio
MCBDDUSNODV2
€16.67
DevDuino Sensor Node V2 is a compact Arduino-compatible microcontroller and is designed to build wireless networks based on transceiver nRF24L01+. You can easily connect other sensors or actuators to this platform, to build your remote monitoring or controlling system.
 2
Available
Electronics

GPS Module GY-GPS6MV2 (U-Blox NEO-6M module...

GPSGYGPS6MV1
€16.67
Seeking for a GPS module with high quality to complete your electronic works? This GY-GPS6MV2 GPS APM2.5 3-5V Module with Antenna is an ideal choice! Adopting high-level electronic components, it is of high accuracy and can react to your operation timely and precisely. The considerate design makes it easy to install and operate. Moreover, with premium...
 2
  • Reduced price / -€1.70
Available
Power and Energy

Grove - XBee Carrier Charging Lipo and solar

MCBGROVXBEECAR
€16.30 €18.00
Charging Lipo and solar XBee Carrier is a Wireless Sensor Network (WSN) base board designed for Bee series and groves. It is primarily suitable for standalone Bee Nodes like RN-171-XV WiFly, RFBee, Wifi Bee. Besides a Bee receptacle, there are also two Grove connectors. The board cab be powered by a lithium battery or through USB cable. You can use a...
  • Reduced price / -€10.00
Available
Electronics

433Mhz wireless PIR Motion Sensor

SENWIRPIR
€7.00 €17.00
This is a wireless PIR for your home automation project. With its included batteries, just install it on your wall and voilà, a new door motion sensor !
Product added to wishlist
Product added to compare.