CoreInk Proto Base is a DIY expansion kit suitable for CoreInk master control. When stacking the expansion board, the IO bus on the CoreInk main control will be led out to the PROTO board through the lower PIN pin. You can design and build the circuit according to your own needs. The package also contains a variety of expansion parts (HY2.0-4P female...
RFID2 is a radio frequency identification unit. Built-in WS1850S chip, working frequency is 13.56MHz. Supports reading card, writing card, recognition, recording, and encoding RF card Multiple functions such as authorization and authorization. Use magnetic field induction technology to realize non-contact two-way information interaction, read...
This shield delivered ready to use, is designed to be mounted directly on an Arduino® board(not delivered). It includes 1 joystick, 4 push buttonsand 2 other miniature push buttons. Ideal for controlling your projects.
UHF-RFID is an ultra-high frequency (UHF) embedded wireless radio frequency reader module. The JRD-4035 module solution with built-in ceramic antenna completely eliminates the technical uncertainty that ordinary UHF modules need to be equipped with additional antennas for users. Optimize the RF design to realize the low power consumption and...
The RTC module is specifically designed for Raspberry Pi. It communicated with Raspberry Pi through I2C bus. There is a Maxim DS1307ZN+ and CR1220 button cell on the board to keep the real time for a long time after the Raspberry Pi has its power down. Set a serial port, TTL convenient way online debugging.
Isolated RS485 Unit is an isolated half duplex transceiver based on the RS485 bus protocol. It can convert TTL level to RS485 level. Since various electrical noises and transient changes of voltage and current may affect communication, Using CA-IS3082W as an interface chip can effectively shield the above noise and provide sufficient...
The analog-to-digital converter(ADC) is a common accessory for Raspberry Pi. This is a 4-channel ADC based on Texas Instrument's ADS1115, which is a precision, low-power, 16-bit ADC chip. We make this ADC into a compact Raspberry Pi Zero form factor and integrated an analog Grove connector so that you can also use analog Grove modules with it.
This is a breakout board for the handy CD74HC4067 16-channel analog / digital multiplexer / demultiplexer. This chip is like a rotary switch - it internally routes the common pin (COM in the diagram, SIG on the board) to one of the 16 channel pins (CHANxx). It works with digital and analog signals (the voltage cannot be higher than VCC), and the...
SIM 800L est un module mini-GSM qui offre des données GSM 2G et GPRS. Désormais également en pack avec la carte SIM ThingsMobile. Le module a une petite taille et une faible consommation d'énergie. Deux fois la taille d'une pièce et 1 mA en mode veille.
Il utilise une interface de communication série, prend en charge les commandes 3GPP TS 27.007, 27.005...
FT232RL breakout. The FT232RL is a USB to serial UART interface with optional clock generator output. It’s the essential tools for establishing communication between PC and mostly MCU. Especially, it’s the optimum tool for basic boards without without USB interface, like arduino pro, colorduino, etc.
CH375 is a USB bus universal interface chip, supports USB-HOST Mode and USB-DEVICE/SLAVE Mode. There are 8-bit data bus and read, write, chip select control wire and interrupt output in CH375.It is convenient to link CH375 to control system bus of MCU/DSP/MPU.CH375 also provides serial communication in USB-HOST mode. It connects with DSP/MCU/MPU through...
BC-04 K/ HC05 Bluetooth R2 Prototype Breakout Board Kit
It is the bottom board of BC04-BK, support most common type bluetooth core board: BC04-B, EC04-B, support HC05
Maxium input voltage 7V, LDO XC6206
Output pins: Key, TXD, RXD, 3V3, 5-7V, GND.
Key is designed for BC04 to clear the pairing status, can connect to a push key.
The LIS3DSH has dynamically selectable full scales of ± 2g / ± 4G / ± 6g / ± 8G / ± 16g, and it is capable of measuring acceleration at output data rates from 3.125 Hz to 1.6 kHz.
The self-test function allows the user to check the functionality of the sensor in the final application.
The device can be configured to generate an interrupt signal for...
DS3231 is a low-cost, extremely accurate I2C real-time clock (RTC), with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. Compared to the DS1302 solution, the DS3231 has many advantages, it function with a VCC ranging from 2.3V to 5.5V and has a battery backup. Unlike
Using brand new double MOS AOD4184A parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment; Wide voltage, the perfect support for PWM; Easy control of power equipment.
L9110 driver can control Reversible with mounting holes compatible steering rudder propeller control quality and high efficiency. 20cm making it easy to blow out the flame can be used outside of the fire lighter robot, robot design and development of essential
This module power supply of 5V, computer debugging USB to TTL serial port. 800MA power supply output current , TTL serial port compatible with 3.3V and 5V MCU, the MCU can be connected directly.
IPX antenna interface can switch PCB antenna, glue stick antenna and sucker antenna.
SIM800L 4 frequency data communications, globally available.
CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus.
LoNet is a GSM and GPS two-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation.
It features ultra-low power consumption in sleep mode and integrated with charging circuit for Li-Ion batteries, that make it get a super long standby time...
A simple rotary encoder for all your projects.
It's like a potentiometer, but without end. It sends pulse to your microcontroller to let you know in which direction it turned. This version also has a button.
This is a T-Cobbler breakout kit used for extending the GPIO interface on Raspberry Pi B+,2 3 4 to breadboard. It helps you to make the connections between Raspberry Pi B+/2/3/4 breadboard become simple.
The RTC module is specifically designed for Raspberry Pi. It communicated with Raspberry Pi through I2C bus. There is a Maxim DS1307 and CR1220 button cell on the board to keep the real time for a long time after the Raspberry Pi has its power down. Set a serial port, TTL convenient way online debugging.
If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. This logic level converter is a small device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V. This level converter also works with 2.8V and 1.8V devices. Each level converter has the capability of converting 4 pins on the high side to 4...
IC AD9850 is an ADI DDS chip which be common used in many DDS projects. This AD9850 DDS module is basic on this ADI AD9850 chip. This module provide you a ready made hardware and you can use serial or parallel pins on board to control the AD9850 for different frequency out put. The duty can be adjust by a adjustable resistor - which change the adjust...