Your cartThere are no more items in your cart
This cheap 16x1 characters lcd is perfect for use with an arduino or any other microcontroller to display data quickly. It is compatible with the Hitachi HD44780 lcd driver.
This very popular LCD Keypad shield can be directly plug on an Arduino board, no soldering or fly-wiring needed.
The 2.4”TFT with Touch Shield is designed for all the Arduino compatible boards. It works in 3.3V voltage level (but with necessary switches from arduino 5v). It can be directly plugged on the Arduino and other compatible boards. It will offer the display, touch and storage function for the Arduino board.
This is a GOG 128x64 Graphic LCD module (controller sed1565). It has an Yellow mode STN panel composed of 128 segments and 64 commons. The LCM can be easily accessed by microcontroller via parallel 6800 series interface.
Very high quality serial lcd with backlight, to add a graphic display to your project in minutes, without the need of much IO lines with fast refresh rate.
This cheap 20x4 characters lcd is perfect for use with an arduino or any other microcontroller to display data quickly. It is compatible with the Hitachi HD44780 lcd driver.
Nokia 5110 LCD is a low-cost 84*48 pixels graphic LCD. It uses the PCD8544 controller. The PCD8544 interfaces to microcontrollers through a serial bus interface (5-wires).
Character LCM screen is a common display device, we provide 16×2 with Blue black light LCD. But these LCD need more than 6 pins for controlling and you need to know the control register and time series. This one is a bit different, you just send the message and voilà ! Only two pins :)
Do you like Amazon Kindle’s E-paper screen? E-ink Display Shield, an E-paper & shield which uses exactly the same techniques, provides you a smooth and clear reading experience for you. It has a super-low power consumption. It won’t consume power until next refreshing of its screen, which enables it to maintain a clear display even in the power-off...
LED 128×64 Display module is an OLED monochrome 128×64dot matrix display module with Grove 4pin I2C Interface .The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. It has bigger screen and uses all the columns from the...
Twig/Grove - OLED 96x96 twig is a 16 color grayscale 96×96 dot matrix OLED display module with Grove compatible 4pin I2C interface.Twig - OLED 96x96 is constructed with 96 x 96 dot matrix OLED module ([ LY120])and SSD1327 driver IC. The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim / thin outline,...
This is a framed graphical LCD 64x128 with yellow or blue black-light . This unit is a very clear STN type LCD with a simple command interface.
The ITDB02 LCD modules works in 3.3V voltage level and are not compatible with Arduino pins, for that reason, this Arduino shield connects with these LCDs. Now you can directly plug the ITDB02 Series LCDs in the shield and stand on the Arduino board.
The ITDB02 LCD modules works in 3.3V voltage level and are not compatible with Arduino Mega pins, for that reason, this Arduino MEGA shield connects with these LCDs. Now you can directly plug the ITDB02 Series LCDs in the shield and stand on the Arduino board.
To facilitate the use of Raspberry Pi and screen module to work together, we specifically developed a simple adapter board and customized a batch of 26-pin (2X13) cable . Simply insert the screen module into the adapter board, then connect the board and Raspberry Pi plate with cable, thus the hardware connection is done, saving the trouble of...
MD070SD adopts 8080 timing sequence with 16-bit parallel bus interface, resolution of 800 × 480, display panel with 16M color and integrated with 8-page video memory (the remaining memory could be used as extended memory). The interior of module utilizes CPLD + SDRAM mode to drive RGB interface display, which does not only realize conversion between the...
Tiny OLED display with a crisp 128x64 resolution that supports a lot of control modes : I2C (2 wires), SPI 3 wires, SPI 4 wires, 8080, etc. depending on your needs. Supporting both 5v and 3.3v, this display can be used with an Arduino, a Raspberry Pi, an STM32 mcu, etc. Oh, and did I mention it was cheap, like in a really low price at a great quality ? It...
Very simple to use plug and play display for the BeagleBone
This great little display boasting a 176X220 resolution has a wide support for all your MCU and little ARM/Linux-based boards. It will work on Arduino, STM32, Raspberry Pi and others.Oh, did I mention it also has an SD card slot ? Making it maybe one of the best value display we can have to offer.