Gear Set (motor + tire)

MOTCARGEARTIRE
€4.00

Very simple ready to use set, ideal to use in small micro-controller vehicles.

You might also like

HackSpark
  1. All our products are shipped from France.
  2. A doubt about a purchase ? Return your items and get money back.
  3. We carefully choose and test the products we sell.

Total weight: 67g

Gear Motor:
Operating voltage: 3V ~ 12V DC (recommended value is 6 ~ 8V)
Maximum torque: 800g.cm (3V)
Speed without load: 170RMP (3V)
Reduction ratio: 1:48
Load current: 70mA (250mA MAX) (3V pm)
With EMC, it has strong anti-interference ability and causes no interference to micro-controller.

Gear tire:
Center hole: 5.3MM x 3.66MM
Diameter: 66MM
Width: 2.66MM

 

27 Items
New product
No reviews

Customers who bought this product also bought:

Available
Home

8-channel Bi-directional Logic Level Converter...

CNVELD8CH
€4.40
This is a breakout board based on TXB0108 IC, the chip can provide bidirectional level shifting from any voltage to any voltage conversion, direction can be auto detected.
2
  • Reduced price / -€3.50
Available
Dev. Tools

FunDuino UNO (ATMega 328P board compatible with...

MCBFUNUNO
€12.50 €16.00
The FunDuino Uno is a microcontroller board based on the Arduino UNO. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer...
2
Available
Electronics

Dual male splittable jumper wires (200mm 40...

CONSEDJMP40P20
€4.17
This is a splittable 40 pin jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
2
Available
Home

Dual stepper motor shield

ASHITEDUASTE
€11.58
Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine.
2
Available
Electronics

3 pin micro switch SPDT with roller 5A

SWIKW4LIMIT
€1.20
Simple micro switch that can be used as a limit switch, as a drawer switch or whatever you'd like. It even support higher current loads, so you can switch motors or high power leds with it (hint hint).
Available
Electronics

Lithium Polymer Battery - 2500mAh 3.7V

ENEBATLP475085
€12.42
This is a light weight, high energy density polymer lithium battery. It outputs a nominal 3.7v at 2500mAh, including built-in protection against over voltage, over current, and minimum voltage. It comes terminated with a standard 2-pin JST connector-2.54 mm spacing between pins. Please do not attempt to charge these with anything but a specialized Lithium...
2
  • Reduced price / -€3.00
Available
Electronics

Bread Board Power Supply Shield (5V/3.3V...

ENEITEBREPOW
€4.50 €7.50
This is a power module for the standard bread boards (Small and Medium sized). It's concave design so will not wast your proto zone. It also supports both 5v and 3.3v (both can be enabled on each power rail). We think it is a must to have on your workbench, really.
2
Available
Electronics

Battery Holder - 3 x AA

ENEBOX3AASWI
€2.08
A prototype AA battery case, , and it can be fully closed by cap and further
Product added to wishlist
Product added to compare.