Your cart
There are no more items in your cart
Raspberry Pi Camera 1.3
SENRPICAM
€16.58
The Raspberry Pi Camera Module is a custom designed add-on for Raspberry Pi. It attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses the dedicated CSI interface, which was designed especially for interfacing to cameras. The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data.
The board itself is tiny, at around 25mm x 20mm x 9mm. It also weighs just over 3g, making it perfect for mobile or other applications where size and weight are important. It connects to Raspberry Pi by way of a short ribbon cable. The camera is connected to the BCM2835 processor on the Pi via the CSI bus, a higher bandwidth link which carries pixel data from the camera back to the processor. This bus travels along the ribbon cable that attaches the camera board to the Pi.
The sensor itself has a native resolution of 5 megapixel, and has a fixed focus lens onboard. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p30, 720p60 and 640x480p60/90 video.
The camera is supported in the latest version of Raspbian, Raspberry Pi's preferred operating system.
Features:
- Small board size: 25mm x 20mm x 9mm
- A 5MP (2592×1944 pixels) Omnivision 5647 sensor in a fixed focus module
- Support 1080p30, 720p60 and 640x480p60/90 video record
Documents:
4 Items
New product
No reviews
Customers who bought this product also bought:
Dev. Tools
433Mhz RF link kit
WIRITE433LINK
€3.92
The 433M RF link kit is consisted of transmitter and receiver, popular used for remote control. 433MHz frequency and ASK modulation.
Dev. Tools
BeagleBone Green (Seeed Studio version)
LINSEDBBGRN
€46.75
€50.00
SeeedStudio BeagleBone Green (BBG) is a joint effort by BeagleBoard.org and Seeed Studio. It is based on the open-source hardware design of BeagleBone Black and developed into this differentiated version.
The BBG has included two Grove connectors, making it easier to connect to the large family of Grove sensors. It has also updated the 5V barrel to micro...
Electronics
Alligator clips test leads set (50cm, 10 wires,...
CONALIGWIRE
€5.50
Color-coded Alligator clips on wires (double ended alligator clip wires)
Prototyping
Test Hooks - Alligator Clips X2
CONALIGCLIPS
€1.25
Those hooks are alligator clips, useful to connect to hard metal or big wires.
Electronics
Dual female splittable jumper wires (200mm, 40...
CONSEDUALFP40P20
€4.17
This is a splittable 40 pin jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Home
Breakout for Raspberry Pi to Breadboard...
BRBRPITCOB
€3.75
This is a T-Cobbler breakout kit used for extending the GPIO interface on Raspberry Pi to breadboard. It helps you to make the connections between Raspberry Pi and breadboard become simple.
Tools
Heatsink Kit for Raspberry Pi B B+ 2-3
ECRRPB1488H
€2.00
Simple heatsink kit for raspberry pi.
Electronics
DC Barrel Power Jack/Connector PCB (5/5.5/2.1mm)
CONBARJACK5521
€1.00
This is a common female barrel jack connector for pcb or cable mounting. 2,1mm inner pole, 5 to 5.5mm outside.
Electronics
DC Power Male Jack Adapter (Screw terminals...
ENEGENBARMSCRM
€1.50
barrel jack This is a DC Jack 5.5/2.1 to screw terminals adapter. It is ideal to connect standard power supplies to your project, led panels, strips or whatever.
Electronics
8mm Red Led
LEDKIN8MMRED
€0.21
Big 8mm red led with low power consumption and high brightness.