Your cart
There are no more items in your cart
Seeeduino Cloud (Arduino compatible Yun openWRT controller)
MCBSEDCLOUD
Last items in stock
€55.00
Seeeduino Cloud is a microcontroller board based on Dragino WiFi IoT module HE and ATmega32u4. HE is a high performance, low cost 150M, 2.4G WiFi module which means “core” in Chinese and with an Open Source OpenWrt system inside. Seeeduino Cloud is also an Arduino compatible board, 100% compatible to grove, shield and IDEs(>=1.5.3). Except for the normal interface of Arduino, Seeeduino Cloud has built-in Ethernet and WiFi support, a USB-A port which makes it very suitable for those prototype design that need network connection and mass storage. It is also a good idea to make Seeeduino Cloud to be an IoT gateway.
Features:
- Compatible with Arduino Yun
- Based on Dragino WiFi IoT module HE
- Open Source OpenWrt system inside
- Support 2.4Ghz WiFi, 802.11 b/g/n
- Support Ethernet
- Support USB 2.0
- Size: 75.10mm x 53.39mm x 11.50mm / 2.95" x 2.10 x 0.45"
- Working temperature: -20~60°C
- Surface colors: Red
Wiki: http://www.seeedstudio.com/wiki/Seeeduino_Cloud
Schematic pdf/jpg: http://www.seeedstudio.com/wiki/File:Seeeduino_Cloud_PDF.pdf
Firmware: http://www.seeedstudio.com/wiki/File:Seeed-build--v1.3.4--20140815-1100.zip
2 Items
New product
No reviews
Customers who bought this product also bought:
Electronics
Dual male splittable jumper wires (200mm 40...
CONSEDJMP40P20
€4.17
This is a splittable 40 pin jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Electronics
10 Resistors pack (1/4w, 1 value, carbon film,...
RES10PACK025W
€0.75
A single pack of 10 resistors of the same value, useful for a single project where you need a particular resistor value.
Electronics
3.7V 3350mAh Li-Ion 18650 Battery (3.2V-4.2V,...
ENEPAN3350
€7.67
Nice little battery that is really inexpensive for the (quite high) power it provides. Be sure to use it with a proper holder.
Dev. Tools
GPS Logger Shield Arduino , Ublox Neo-6M R2
ASHELEGPSSHIELD
€16.58
Arduino GPS shield is a GPS module breakout board for Arduino. It can make your Arduino as a GPS receiver with SD storage, it is easy to use for recording the position data into SD card by Arduino
Relays
4 Channel 5V Relay Module (5V, 250VAC/10A)
RELITD4CH5V
€8.00
This is a 4-Channel Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430.
Electronics
Dual male splittable jumper wires (300mm, 40...
CONSEDJMP40PMM
€5.00
This is a splittable 40 pin dual male jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Power supply
DC 5V 3A Micro USB Power supply (raspberry pi)
ENE5V3AMICUSB
€10.00
DC 5V 3A This small yet powerful 5V DC 3A USB power module provides your mini-computers (only iuse on compliant devices !) an easy to use power supply.
Electronics
Infrared Kit - IR Receiver (HS0038) + IR LED...
IRELDRECTRANS
€0.79
hs0038 IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.