Seeeduino Cloud - Compatible Arduino Yun (Carte OpenWRT)
MCBSEDCLOUDDerniers articles en stock
Seeeduino Cloud is a microcontroller board based on Dragino WiFi IoT module HE and ATmega32u4. HE is a high performance, low cost 150M, 2.4G WiFi module which means “core” in Chinese and with an Open Source OpenWrt system inside. Seeeduino Cloud is also an Arduino compatible board, 100% compatible to grove, shield and IDEs(>=1.5.3). Except for the normal interface of Arduino, Seeeduino Cloud has built-in Ethernet and WiFi support, a USB-A port which makes it very suitable for those prototype design that need network connection and mass storage. It is also a good idea to make Seeeduino Cloud to be an IoT gateway.
- Compatible with Arduino Yun
- Based on Dragino WiFi IoT module HE
- Open Source OpenWrt system inside
- Support 2.4Ghz WiFi, 802.11 b/g/n
- Support Ethernet
- Support USB 2.0
- Size: 75.10mm x 53.39mm x 11.50mm / 2.95" x 2.10 x 0.45"
- Working temperature: -20~60°C
- Surface colors: Red
Schematic pdf/jpg: http://www.seeedstudio.com/wiki/File:Seeeduino_Cloud_PDF.pdf
Les clients qui ont acheté ce produit ont également acheté...
Connecteurs et Fils
USB to TTL Cable, specialized for dev boards. 5V et 3.3V
IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.
7,50 € 12,00 €
C'est une antenne GPS Active à utiliser avec tous nos modules ou shields GPS. Le cable fourni fait 3 Mètres. Magnetic
The 7” Touch screen Monitor for Raspberry Pi gives users the ability to create all - in - one, integrated projects such as tablets, infotainment systems and embedded projects. The 800 x 480 display connects via an adapter board which handles power and signal co nversion. Only two connections to the Pi are required; power from the Pi’s GPIO port and a...
Simple 5mm green led with 20mcd power.
This is a splittable 40 pin dual male jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
This is a digital temperature sensor, that is already calibrated. The measurement is done where the sensor is, no need for long insulated wire or complicated ADC design. This sensor is therefore also perfect for use with a Raspberry Pi, as it is not analogic, all the data is transmitted in digital One Wire protocol.
Connectivité sans fil
4,00 € 5,00 €
This is the pin compatible upgrded version of the ESP-01 chip. ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP8266 has...
Radio (2.4Ghz, 868Mhz, 433Mhz, etc.)
USB wireless serial data transmission module, support AT commands. With a stable CH340T do USB to serial.With this module you can do wireless serial distance transmission (100 ~ 1100m, depending on the use of the wireless module).
This is a splittable 40 pin jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.