Your cart
There are no more items in your cart
ESP-32-DevKitC NodeMCU-like dev. board for ESP32 (Based on ESP-WROOM-32D, Wifi and Bluetooth 4.0)
WIRELE32DEVKIT
€10.00
ESP32-DevKitC is a low-footprint, minimal system development board which is powered by our latest ESP-WROOM-32 module and can be easily adjusted to a breadboard.
-
Product Description
ESP32-DevKitC is a low-footprint, minimal system development board which is powered by our latest ESP-WROOM-32 module and can be easily adjusted to a breadboard.
- Rapid Prototyping – Get right into application design and development without worrying about RF performance and antenna design. The ESP32-DevKitC has your basic system requirements already covered. Just plug in the USB cable and you’re good to go!
- Flexible and Feature-Rich – The ESP32-DevKitC contains the entire basic support circuitry for the ESP-WROOM-32, including the USB-UART bridge, reset- and boot-mode buttons, LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.
- Breadboard-Friendly – The ESP32-DevKitC pinout is optimized for prototyping on a breadboard. The on-board LDO output is led out for powering additional off-board electronics. Peripheral outputs are grouped together for hassle-free prototyping.
- Core board based on esp-32 WROOM-32 from espressif too.
- Similar to nodemcu board, compact size, on board USB-TTL CP2102, LDO AMS1117, microUSB, flash and reset buttons, etc. Very nice.
- Breadboard friendly.
- On board marked version V2.
- Auto upload bug on windows solution can be found here. Tested up to 10UF can work
4 Items
New product
No reviews
Customers who bought this product also bought:
Sensors
Electronic Brick - Gas Sensor MQ135
Electronic Brick - Gas Sensor MQ
€4.17
MQ-135 Gas Sensor
The gas sensitive material used by the MQ135 gas sensor is tin oxide (SnO2), which has low conductivity in clean air. When the sensor is kept in the polluting gases, the conductivity of the sensor increases with the increase in the concentration of the polluted air. Using a simple circuit can convert the change in conductivity into an...
Electronics
L298 Dual H-Bridge Motor Driver
SESMOT103B1M
€6.67
If you are building a robot with wheels, you need a dual H-Bridge driver like this one.
Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive...
Electronics
male female splittable jumper wires (100mm, 40...
CONSEDJMP40PMF10
€3.33
This is a splittable 40 pin male-female jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Display
1M/60leds WS2812 Digital RGB LED Flexi Strip...
LEDSTR60PMWS2812
€14.00
Digital RGB LED Flexi-Strip is an intelligent light source consist s of WS2812B RGB LED with Integrated Driver Chip. The control circuit and RGB chip are integrated in a package of 5050 components.
This LED flexible strip is a full-color that external control for each lamp beads. It with high brightness, can achieve effects of full color running water,...
Tools
45 in 1 Professional Portable Opening Precision...
TOOLSETJK
€16.67
This 45 in1 Precision multi-non-slip tough shaft ensures greater comfort and convenience. This screwdriver kit set is an ideal tool for repairing electronic workshops, watch, eyeglass, and hobby miniatures where fine precision is required.
Dev. Tools
Battery Shield - (Wemos D1 Mini)
ENEWEMSBAT
€6.00
Completed to make your wemos d1 mini nomadic
Electronics
4 Channel Logic Level Converter Bi-Directional...
CNVJAN4CH
€2.00
he level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV' pin, low voltage (3.3V for example) to ‘LV', and ground from the system to the ‘GND' pin.
Prototyping
Solderable Prototype two holes, three connected...
PROSOLDGPCB23H
€3.00
Layout same as breadboard, and also same connection in the veritcal pin line.
GPS
GNSS Module, GPS Beidou, ATGM336H-5N (Arduino...
GPSELEATGM336
€12.50
GNSS Module, GPS Beidou, ATGM336H-5N
Electronics
3.7V 2900mAh Li-Ion 18650 Battery (3.2V-4.2V,...
ENEPANBATNCR18650PF
€5.83
Nice little battery that is really inexpensive for the (quite high) power it provides. Be sure to use it with a proper holder.