Your cart
There are no more items in your cart
Digital DS18B20 temperature sensor with steel head (waterproof, one-wire)
SENDS18B20METAL
€6.00
This is a digital temperature sensor, that is already calibrated. The measurement is done where the sensor is, no need for long insulated wire or complicated ADC design.
This sensor is therefore also perfect for use with a Raspberry Pi, as it is not analogic, all the data is transmitted in digital One Wire protocol.
- Chip used: DS18B20 (one wire digital temperature sensor)
- Length of Cable : 10cm
- Size of Stainless steel sheath: 6*50mm
- Power supply range: 3.0V to 5.5V
- Operating temperature range:-55°C to +125°C (-67°F to +257°F)
- Storage temperature range:-55°C to +125°C (-67°F to +257°F)
- Accuracy over the range of -10°C to +85°C: ±0.5°C.
- Output leads: Red (VCC), Blue (DATA), Black (GND)
- Waterproof
- For each lead, we use 30pcs tinning lines, which is different from other DS18B20 sensor wires, it is soft and has better oxidation resistance ability
- Flexibility resistance
- Better thermal conductivity
5 Items
New product
No reviews
Customers who bought this product also bought:
Dev. Tools
PRO MICRO 5V/16MHZ Micro USB Leonardo
PROMICRO5V
€8.25
The Pro Micro is an Arduino compatible microcontroller development board based on the ATmega32U4 IC designed by Sparkfun Electronics. It is based around the Arduino Leonardo which means you no longer need an addition USB-Serial Interface to program your Arduino.
leonardo
Electronics
Grove – Air quality sensor
SENSESGROAIR
€16.00
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases.
Prototyping
9x15 Protoboard 2.54mm
PCB00007
€3.50
High quality protoboard gives you 9x15cm of building space for through-hole components with 2.54mm spaced holes.
Dev. Tools
Wemos D1 (ESP8266, Arduino-compatible layout,...
MCBWEMD1
€10.50
€12.50
The D1 is an Arduino Uno-like wifi board based on ESP-8266EX.
11 digital input/output pins
1 analog input(3.3V max input)
a Micro USB connection
a power jack, 9-24V power input.
Compatible with Arduino
Sensors
Weight Sensor Amplifier- HX711
ECRSHX711O
€3.67
€6.67
This aplifier allows you to use weight sensors of all kinds.
Power and Energy
150W Boost Converter DC-DC 12-35V Step Up...
ENEDCDCBOOST150W
€8.25
This is a simple to use DC-DC step-up circuit. Use it to boost a lower voltage to an higher one. This circuit boasts a passive cooling system allowing you to power high power systems (led matrixes or motors for example).
Dev. Tools
ATMega 328 with Arduino UNO R3 bootloader...
ELCARDUNOATM328
€5.50
ATMega328 32K microcontroller with pre-loaded Arduino UNO bootloader
Electronics
10 Resistors pack (1/4w, 1 value, carbon film,...
RES10PACK025W
€0.75
A single pack of 10 resistors of the same value, useful for a single project where you need a particular resistor value.
Electronics
TQFP / LQFP 32-64 to DIP Adapter/Breakout PCB...
PCBITESMDADAQFP3264
€2.09
You can solder a TQFP32/TQFP44/TQFP48/TQFP64 IC in the board and breakout all its pins to the pad around the edge – which 100 mil interval.