MP2315 Mini DC Step-down Power Module 12/24V to 5V3A
ENETAOSTEDUSBLast items in stock
Stepdown 5V USB Output Converter DC 6...24V To 5V 3A Step Down Module
Ideal to get a strong and stable 5v usb output from any source from 6 to 24V.
- The maximum output current of 3A, 2.1A long run, sufficient margin.
- Using a new design, circuit design does not require electrolytic capacitors and tantalum capacitors (electrolytic capacitor life is short, tantalum capacitors have the risk of explosion). Using the current high-end circuit with large-size solid-state ceramic capacitors (MCC) 3pcs.
- Ripple is very low, 12V to 5V 3A only 10 mV or so, a lot of ripple rivals have reached 500 mV or greater, the equipment will cause an invisible injury, serious equipment will cause abnormal or damaged, IPHONE Very delicate.
- The new solution uses synchronous rectification, the circuit conversion efficiency is very high, in the 6.5V to 5V0.7A when the efficiency of up to 97.5%, 12V to 5V1A also reached 94%, unlike some efficiency of only 60-70% peers. (The efficiency test removes the voltage drop across the input reverse-polarity protection diodes and fuses).
- Use of flat copper inductors, to maximize the conversion efficiency. Reduce heat.
- The first with output over-voltage protection, input 1.5A fuse, output 5V 300W TVS tube over-voltage clamp protection to protect USB devices are now peer USB buck module are not over-voltage protection, the USB device There is a very large security risk, think about it put it on your iphone or other phones
- Using the latest USB identification circuit, perfectly compatible with IPHONE, the vast majority of android mobile phones, IPAD.
- Short gold-plated edge USB, long life, not a normal USB interface can match.
- Output voltage indicator (red)Ultra – small size, 26.4 (L) * 15 (W) * 7.4 (H) mm.
- Input with a reverse polarity protection diode, input positive and negative polarity will not be damaged, (OUR test efficiency ignores the input diode and fuse voltage drop)
- Ultra-low quiescent current, quiescent current 0.85 mA. Connect to the car battery without adding the switch, you can connect the cigarette lighter line, or ACC power line.
- Input voltage: DC 6-24V, Output voltage: 5.1-5.2V
- Output current: maximum 3A (full load, please pay attention to heat), the actual test input 12V output 2A no special treatment within the cooling.
- Conversion efficiency: up to 97.5% (6.5 to 5V 0.7A) (short-circuit reverse polarity protection and fuse after the test value)
- Switching frequency: 500KHz
- Output ripple: 10mV or so (12V to 5V3A) 20M bandwidth
- Output indication: The output voltage indicator is red
- Operating temperature: industrial (-40 ℃ to + 85 ℃) (the higher the ambient temperature, the smaller the output power)
- Output overvoltage protection: yes, input 1.5A fuse, output 5V 300W TVS tube clamp protection.
- Full load temperature rise: 30 ℃
- Quiescent Current: 0.85 mA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Output short-circuit protection: Yes, do not short-circuit for a long time
- Input reverse polarity protection: Yes, input reverse polarity protection diode
Customers who bought this product also bought:
This is a light weight, high energy density polymer lithium battery. It outputs a nominal 3.7v at 2500mAh, including built-in protection against over voltage, over current, and minimum voltage. It comes terminated with a standard 2-pin JST connector-2.54 mm spacing between pins. Please do not attempt to charge these with anything but a specialized Lithium...
Chem-Wik® Rosin is especially designed for today’s heat sensitive electronic components. The lighter mass, pure copper braid construction allows for better thermal conductivity, even at low temperatures. Chem-Wik® Rosin responds as much as 50% faster than conventional desoldering braids. This design minimizes overheating and requires less “contact”...
Double BTS7960 large current (43 A) H bridge driver; 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board; voltage indication of motor driver output end; can solder heat sink;
Basic and sturdy 3rd hand to help you on all your prototyping needs. 3rd hand PCB holder (60mm Equipment: magnifying glass)
GY-BME280 is a Breakout Board featuring a Bosch Sensortec BME280 Temperature, Humidity & Pressure Sensor. The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm. Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k,...
High power mosfet to switch all your devices/leds/motors easily. This is the P-type, meaning you have to put it between the load and the ground.
This is a simple sliding switch ready to plug on a protoboard or a breaboard.
Soil moisture module is most sensitive to the ambient, generally used to detect the moisture content of the soil.When the module can not reach the threshold value, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low;The small board digital output D0 can be connected directly to the MCU, MCU to detect...
Wide input voltage value from 5V to 32V, you can always get a constant output voltage from 1.25 to 35V adjustable.
Digital RGB LED Flexi-Strip is an intelligent light source consist s of WS2812B RGB LED with Integrated Driver Chip. The control circuit and RGB chip are integrated in a package of 5050 components. This LED flexible strip is a full-color that external control for each lamp beads. It with high brightness, can achieve effects of full color running water,...