Your cart
There are no more items in your cart
Dual male splittable jumper wires (100mm, 40 pins) (cable)
CONSEDJMP40PMM10
€3.33
This is a splittable 40 pin dual male jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Cables of 100mm, 2 male pin, 40 wires assembled as one splittable cable.
50 Items
New product
No reviews
Customers who bought this product also bought:
Electronics
1m Cable (0.22mm², AWG-24, 300v peak) fils...
CAB1MAWG24
€0.42
White Grey Black Red blue green /// Nice cable with a smaller section, ideal for a lot of electronic board to board wiring.
Electronics
WTV020-SD Music/Voice Play Module MP3 (Micro...
SNDELDWTV020SD
€6.75
This very tiny module (the size of the micro sd card reader) reads voice and music from the sd card, as needed from your micro-controller.
Electronics
4 Channel Logic Level Converter Bi-Directional...
CNVJAN4CH
€2.00
he level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV' pin, low voltage (3.3V for example) to ‘LV', and ground from the system to the ‘GND' pin.
Electronics
Screw terminal 3P 5.0mm pitch
CONSCRTERMDG300503P12
€0.92
Simple 5.0mm 3 pins screw terminal. Can be chained to make longer terminal blocks. This termina can fit perfectly on a breadboard to connect remote peripherals.
Wires and Connectors
Stereo Jack 3,5mm, 3.5mm Straight Panel Mount
CONTAOJACKSPAN
€1.50
Stereo Jack 3.5mm, 3.5mm Straight Panel Mount
Electronics
BPW34 Photo diode, Vishay, visible light + IR,...
ECJMOUBPW34
€1.00
BPW34 Photo diode, Vishay, visible light + IR, 65 °, Si, Through-beam
Electronics
Lithium Polymer Battery - 2500mAh 3.7V
ENEBATLP475085
€15.00
This is a light weight, high energy density polymer lithium battery. It outputs a nominal 3.7v at 2500mAh, including built-in protection against over voltage, over current, and minimum voltage. It comes terminated with a standard 2-pin JST connector-2.54 mm spacing between pins. Please do not attempt to charge these with anything but a specialized Lithium...
Arduino
CNC Shield for Arduino (GRBL Arduino Compatible)
ASHCNCGRBLKIT
€6.67
The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepper motors using 4x A4988 or DRV8825 with this shield and an Arduino you can build all kinds of robotics or CNC projects including CNC routers, laser cutters and even pick&place machines. This is the KIT...
Dev. Tools
BeagleBone Black (Rev. C)
LINBEAGLEBONEBLK
€55.83
BeagleBone Black is the newest member of the BeagleBoard family and is a lower-cost, high-expansion focused BeagleBone, featuring the Sitara AM3359 ARM Cortex-A8 32-Bit RISC microprocessor from Texas Instruments. It is similar to the BeagleBone but with some previous features removed to make way for the excellent new features.
Electronics
Bread Board Power Supply Shield Micro USB...
ENEITEBREPOW
€3.50
€7.50
This is a power module for the standard bread boards (Small and Medium sized). It's concave design so will not wast your proto zone. It also supports both 5v and 3.3v (both can be enabled on each power rail).
We think it is a must to have on your workbench, really.