Dial-Type Potentiometer (46mm/22mm, 10k)

IHMPOTDIAL10K
Last items in stock
€15.83

Potentiometer is one of the most useful basic components. This is a 10k dial type potentiometer with knob. It’s space-saving and user-friendly. You can read the actual resistance value via the straightforward knob without auxiliary instrument like multimeter. Each has been pre-calibrated. You can implement it into your circuit right out of the box. A tiny hex wrench is included in case of recalibration.

You might also like

HackSpark
  1. All our products are shipped from France.
  2. A doubt about a purchase ? Return your items and get money back.
  3. We carefully choose and test the products we sell.
Features
  • Straightforward
  • Highly linear
  • Space-saving
Specifications
  • Max resistance: 0 - 10KΩ
  • Accuracy : ±5%
  • Lin : ±0.25%
  • Max mechanical angle : 3600° 
  • Dimensions: 46mm(height) * 22mm(diameter)
1 Item
New product
No reviews

Customers who bought this product also bought:

2
  • Reduced price / -€7.00
Available
Dev. Tools

D-DUINO OLED 0.96 (ESP8266, WIFI, 32bit mcu)

WIRNODMCUDDUINO
€13.00 €20.00
D-duino can be programed like Arduino. It has a display(0.96 inch OLED) so I call it D-duino. Also you can use LUA  control this board like NodeMCU. You can understand this is NodeMCU+OLED. I think the 0.96″ OLED will be very helpful for makers to develop IOT.
2
Available
Electronics

3.3V Low-Cost Laser Pointer - Red Point

LASLCO33V
€1.25
This laser pointer or laser pen is a small handheld device with a laser diode emitting a very narrow coherent low-powered laser beam of visible light, it is frequently used in lecture halls and demonstrations to point at topics of interest on a presentation board. In a school setting, they have become ubiquitous, and they are very useful teaching aids....
2
Available
Display

7-segment clock display - 0.39" digit height...

LED7SEG039GR
€0.83
Design a clock, timer or counter into your next project using this pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal points on each digit and an extra wire for colon-dots in the center (good for time-based projects) and a top right hand dot which could be...
Available
Electronics

A4988 stepper motor driver with heat sink...

MDRA4988
€6.25
The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase...
  • Reduced price / -€5.17
Available
Electronics

9 Axis Automatic integrated IMU GY-951...

SINIMUGY951
€19.83 €25.00
Using sensors ITG3205, ADXL345, HMC5883L and an integrated ATMEGA328P this 9 Axis integrated IMU will directly output yaw, roll and pitch information for your next robotic project !
2
Out of stock
Dev. Tools

MotoMama - L298N H-Bridge Motor Driver Shield

MOTDRIITEMOTMAM
€12.50
MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motors with Arduino boards.
View
Product added to wishlist
Product added to compare.