SD Card Reader Module - ARM MCU Read And Write (Arduino Compatible)

MODSDSOCKET
€2.42

Brand new and high quality. SD Card module can make your SD application more easier and simple.

HackSpark
  1. All our products are shipped from France.
  2. A doubt about a purchase ? Return your items and get money back.
  3. We carefully choose and test the products we sell.
  • It is easily interfaced as a peripheral for arduino sensor shield module.
  • Through programming, you can read and write to the SD card using for arduino.
  • Can be used for SD Card more eaisly, such as for MP3 Player, MCU/ARM system control.
  • All SD SPI pins output, MOSI, SCK, MISO and CS.
  • Support 5V/3.3V input.
  • Size:5.1cm x 3.1cm - 2.01inch x 1.22inch.
21 Items
New product
No reviews

Customers who bought this product also bought:

Available
Dev. Tools

Arduino-Compatible Pro Mini [16M/5V, 8M/3V3]

MCBARDPROMIN
€5.42
The minimal design approach to EDArduino, and fully compatible with arduino. This is a 5V EDArduino running the 16MHz bootloader (select ‘Arduino pro mini′ within the Arduino software). EDArduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time EDArduino...
2
  • Reduced price / -€5.50
Available
Dev. Tools

nRF24L01+ with PA and LNA 2.4Ghz RF module...

WIRITENRF24L01PALNA
€6.50 €12.00
This is a long distance 2.4G wireless module which basic on nRF24L01+ chip, and there is the PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.
2
  • Reduced price / -€6.00
Available
Electronics

ADXL345 Accelerometer breakout module Triple-Axis

SENITEADXL345
€4.00 €10.00
The ADXL345 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned voltage outputs. The product measures acceleration with a minimum full-scale rangethe static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration.
2
Available
Electronics

Micro SD Card Reader Module - SPI interfaces...

MODJANMCSDCTF
€2.42
Support Micro SD card(<=2G), micro SDHC card(<=32G)Interface level: 5V  or 3.3VPowr supply: 4.5V to 5.5V , 3.3V voltage regulator circuit boardCurrency: 0.2-200mACommunication interface: SPIWith 4 holes for M2 screw. Easy to install
2
Available
Electronics

3x7 Protoboard

PCBPROTO3X7
€1.50
no odor finely drilled tough including power pad. Clean hole
2
Available
Electronics

PN532 NFC MODULE

WIRITENFCPN532
€16.00
PN532 NFC module, as its name implies, is based on PN532 chip and used for 13.56MHz near field communication. The module is equipped with onboard antenna, thus no external antenna coil is needed. It is compatible with SPI, IIC and UART interface for communication. With NFC library support for Arduino and Raspberry Pi offered by us, it is quite convenient...
2
Out of stock
Electronics

Dual male splittable jumper wires (100mm, 40...

CONSEDJMP40PMM10
€3.33
This is a splittable 40 pin dual male jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
View
Product added to wishlist
Product added to compare.