Drivers

Out of stock
Electronique

TB6612FNG Dual H-Bridge Motor Drive Board

SESMOTB6612
4,17 €
is a great dual motor driver that is perfect for interfacing two small DC motors such as our micro metal gearmotors to a microcontroller, and it can also be used to control a single bipolar stepper motor. The MOSFET-based H-bridges are much more efficient than the BJT-based H-bridges used in older drivers such as the L298N and Sanyo’s LB1836M, which...
View
2
Available
Robots

Programmable Spin: bit basé sur Micro: bit...

LEGYAHBMBIT
30,00 €
Programmable Spin: bit basé sur Micro: bit compatible avec LEGO https://hackspark.fr/en/electronics/2236-motor-driver-pour-microbit-tb6612fng.html non fourni https://hackspark.fr/en/microbit-bbc/2232-carte-microbit-bbc.html non fourni
2
Available
Outils de dev.

SSC-32U USB 32 Servo Controller Atmega 328P

ECRACSPWM32
33,33 €
Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts
Available
Electronique

High Power Mosfet Drive Module, PWM Control

DRIELDHPW
2,92 €
Using brand new double MOS AOD4184A parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment; Wide voltage, the perfect support for PWM; Easy control of power equipment.
2
Available
Drivers électroniques (de moteurs, etc.)

TB6560 Motor driver (max 3A, 10-35v motor,...

MDRTB65603A
10,00 €
A quite powerful motor driver, taking from 12v to 24v as input. It even has opto-couplers to separate your driving electronics from the motor power.
2
Available
Electronique

Driver de moteur avec dissipateur thermique...

MDRDRV8825
6,25 €
This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for...
2
Out of stock
Outils de dev.

MotoMama - L298N H-Bridge Motor Driver Shield

MOTDRIITEMOTMAM
12,50 €
MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motors with Arduino boards.
View
2
Available
Motorisé

Shield Moteur pour Arduino VNH2SP30

ASHSESMOTV2
16,58 €
Description This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm...
  • Prix réduit / -1,50 €
Available
Electronique

Driver de moteur avec dissipateur thermique...

MDRA4988
4,75 € 6,25 €
The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase...
  • Prix réduit / -2,00 €
Available
Electronique

ULN2003 Stepper Motor Driver Board

iTeadStudio
MDRULN2003
2,58 € 4,58 €
ULN2003 Stepper Motor Driver Board is use the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motors (5v-12v).
2
Available
Electronique

EasyDriver allegro stepper motor driver

MDREASYDRIVER
5,00 €
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and...
  • Prix réduit / -9,00 €
Available
Electronique

L298 Dual H-Bridge Motor Driver

SESMOT103B1M
3,50 € 12,50 €
If you are building a robot with wheels, you need a dual H-Bridge driver like this one. Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive...
Drivers
Product added to wishlist
Product added to compare.