Accessoires

Available
Electronique

Battery Holder - 1 x AA

ENEITEBOX1AA
1,58 €
A prototype AA battery case, it has on/off switch on the case, and it can be fully closed by cap and further screw it to close, so it’s very well protected.
 2
Available
Moteur et servo-moteurs

EC3 Connecteurs M/F

CONEC3MF
2,08 €
Connecteur à souder prise EC3 F/M
 2
Available
Motorisé

FPV Bracket Kit avec 2 servo SG90 (Robotique)

MECFPV9GBRA2
16,67 €
This is the FPV Bracket Kit woth 9g Servo, with the help of this product, it would be easy for you to create 3-axis projects such as environment monitoring, tracking. It would be you good partner in servo related projects.
Available
Electronique

Accéléromètre, 3 Axes, ADXL345BCCZ, I2C, SPI...

Analog Devices
SENITEADXL345SMD
7,50 €
L'ADXL345 est un accéléromètre 3 axes consommant peu d'énergie, sortant des signaux de voltage conditionnés tout en gardant une taille très réduite. Son prix très bas vous permettra de l'inclure dans tous vos montages sans y réfléchir à deux fois.
 2
Available
Electronique

CJMCU LIS3DH Module d'accélération 3 axes...

SENJANLIS3DH
10,00 €
Le LIS3DSH a des pleines échelles sélectionnables dynamiquement de ± 2g / ± 4G / ± 6g / ± 8G / ± 16g, et il est capable de mesurer l'accélération à des débits de données de sortie de 3,125 Hz à 1,6 kHz.   La fonction d'auto-test permet à l'utilisateur de vérifier la fonctionnalité du capteur dans l'application finale.   L'appareil peut être configuré pour...
Available
Electronique

Battery Holder 6 x AA Barrel Jack

ENEFLYBOX6AA
4,00 €
The 6x AA Battery Holder puts a nice finishing touch on your battery powered project.
 2
Out of stock
Outils de dev.

MotoMama - L298N H-Bridge Motor Driver Shield

MOTDRIITEMOTMAM
12,50 €
MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motors with Arduino boards.
 2
Available
Motorisé

FPV Bracket Kit pour 9g Servo (Robotique SG90...

MECFPV9GBRA
7,08 €
This is the FPV Bracket Kit For 9g Servo, with the help of this product, it would be easy for you to create 3-axis projects such as environment monitoring, tracking. It would be you good partner in servo related projects.
 2
Available
Electronique

Battery Holder - 3 x AA

ENEBOX3AASWI
2,08 €
A prototype AA battery case, , and it can be fully closed by cap and further
 2
Available
Electronique

Module accéléromètre ADXL345 Triple-Axis

iTeadStudio
SENITEADXL345
6,67 €
L'ADXL345 est un accéléromètre 3 axes consommant peu d'énergie, sortant des signaux de voltage conditionnés tout en gardant une taille très réduite. Son prix très bas vous permettra de l'inclure dans tous vos montages sans y réfléchir à deux fois.
 2
Available
Electronique

GY-61 Module accéléromètre low-cost ADXL335...

iTeadStudio
SENITEADXL335
8,00 €
L'ADXL335 MMA7361L est un accéléromètre 3 axes consommant peu d'énergie, sortant des signaux de voltage conditionnés tout en gardant une taille très réduite. Son prix très bas vous permettra de l'inclure dans tous vos montages sans y réfléchir à deux fois.
Available
Electronique

Battery Holder - 4 x AA

ENEITEBOX4AA
2,50 €
A prototype AA battery case, it has on/off switch on the case, and it can be fully closed by cap and further screw it to close, so it’s very well protected.
 2
Available
Outils de dev.

433Mhz RF link kit

iTeadStudio
WIRITE433LINK
3,92 €
The 433M RF link kit is consisted of transmitter and receiver, popular used for remote control. 433MHz frequency and ASK modulation.
 2
Available
Electronique

Freescale MMA7361L Accelerometer breakout...

iTeadStudio
SENITEMMA7361L
9,00 €
This is a breakout board for Freescale's MMA7361L three-axis analog accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and...
Available
Outils de dev.

nRF24L01+ 2.4Ghz RF module (improved range)

iTeadStudio
WIRITENRF24L01
4,00 €
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+.This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401+ and add some extra pipelines, buffers, and an auto-retransmit feature.
Available
Electronique

L298 Dual H-Bridge Motor Driver

SESMOT103B1M
6,67 €
If you are building a robot with wheels, you need a dual H-Bridge driver like this one. Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive...
Product added to wishlist
Product added to compare.