Autres

 2
Available
Senseurs

Tube/Air Pressure Unit MCP-H10-B200KPPN Capteur...

SENJANPRESH10
10,83 €
Tube pressure is a wide range air pressure sensor that supports -100 ~ 200Kpa. You can connect one end of the tube to the gas inlet. This sensor transmitted onto mapping value -100 ~ 200Kpa and 0.1 ~ 3.1V voltage output. Also having a protective housing for long term stability. It’s an accessory that your industrial use cannot live without.
 2
Available
Grove

M5stack Unité de lecture d'empreintes digitales...

SENM5S1020A
23,33 €
La descriptionL'unité FINGER est un capteur d'empreintes digitales basé sur le chipset FPC1020A.Ce capteur d'empreintes digitales tout-en-un simplifie l'ajout, la vérification et la gestion des empreintes digitales.Exploité par le protocole UART, sa taille compacte et sa consommation d'énergie ultra-faible le rendent très attrayant à utiliser autour du...
 2
Available
Outils de dev.

Unit Kit for M5StickC Hat ENVIII SHT30 QMP6988

M5STIKITENVIII
11,25 €
ENV III HAT est un capteur environnemental multifonctionnel adapté à la série M5StickC. Il intègre SHT30 et QMP6988 en interne pour détecter les données de température, d'humidité et de pression atmosphérique. SHT30 (0x44) est un capteur de température numérique haute précision et basse consommation. Capteur d'humidité. QMP6988 (0x56) est un capteur de...
 2
Out of stock
Grove

M5stack Grove U090 - Capteur de pression...

BARM5SGRBMP280
5,00 €
L'unité de pression barométrique est une unité de baromètre qui intègre le capteur de pression Bosch BMP280 pour mesurer la pression atmosphérique et estimer l'altitude. La précision relative peut atteindre ± 0,12 hpa, ce qui équivaut à une différence de hauteur de ± 1 m. Dans le même temps, le coefficient de dérive en température est très faible, pouvant...
 2
Available
Senseurs

M5STACK U107 - Unité de lecture RFID UHF JRD-4035

SENM5SRFIDUHF
70,00 €
Description UHF-RFID is an ultra-high frequency (UHF) embedded wireless radio frequency reader module. The JRD-4035 module solution with built-in ceramic antenna completely eliminates the technical uncertainty that ordinary UHF modules need to be equipped with additional antennas for users. Optimize the RF design to realize the low power consumption and...
 2
Out of stock
Electronique

capteur d'humidité du sol capacitif (arduino...

SENGENMOISTV2
4,92 €
Soil moisture module is most sensitive to the ambient, generally used to detect the moisture content of the soil.When the module can not reach the threshold value, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low;The small board digital output D0 can be connected directly to the MCU, MCU to detect...
 2
Out of stock
Grove

Grove - Barometer Sensor(BMP280) M5stack

BARM5SGRBMP180
5,00 €
Barometric Pressure Unit is a barometer unit, which integrates the Bosch BMP280 pressure sensor to measure atmospheric pressure and estimate the altitude. The relative accuracy can reach ± 0.12hpa, equivalent to ± 1m height difference. At the same time, the temperature drift coefficient is very low, which can reach 1.5 PA / K, that is, the temperature...
Out of stock
Electronique

AD597ARZ - CI de capteur de température,...

Analog Devices
ECJMOUAD597
10,00 €
The AD597ARZ is a monolithic temperature Set-point Controller which has been optimized for use at elevated temperatures such as those found in oven control applications. The device cold junction compensates and amplifies a type J or K thermocouple input to derive an internal signal proportional to temperature. The internal signal is then compared with an...
 2
Available
Outils de dev.

Unit Kit for M5StickC Hat ENVII SHT30 BMP280...

MCBM5STIKITENVII
11,25 €
ENV II HAT est un capteur d'environnement qui peut détecter la température, l'humidité et la pression atmosphérique. Il est construit avec des capteurs SHT30, BMP280 et BMM150, il est programmé sur I2C. SHT30 est un capteur numérique de température et d'humidité de haute précision et à faible consommation d'énergie. Le BMP280 est un capteur de pression...
 2
Available
Electronique

Magnetic Door Switch 23x13,9x5,9mm...

SWISESDOORONO
5,42 €
Senses when a door or window is open or closed... Perfect for use with your favourite micro controller board (be it arduino, launchpad, stm3é or whatever) !
 2
Available
Senseurs

MLX90614 mesure de température par infrarouge...

SENJANGY906
10,42 €
MELEXIS MLX90614ESF-BAA-000-TU-ND Thermomètre infrarouge sans contact à utiliser avec (pour) Arduino, ou tout microcontrôleur pouvant communiquer avec lui via son interface I2C. Ce capteur est livré avec une carte opto-isolée avec tous les composants nécessaires au fonctionnement et deux types de broches. Ils sont déssoudés. Veuillez indiquer si vous...
 2
Available
Electronique

8128 CCS811 + HDC1080 + BMP280 Gaz Température...

SENJAN8128
15,00 €
CCS811 + HDC1080 + BMP280 faible puissance Gaz Température et Humidité Hauteur Trois-en-un Capteur Module de surveillance la qualité de L'air intérieur
 2
Out of stock
Electronique

RTC& EEPROM Module DS3231 AT24C32

iTeadStudio
SENSEDIICRTCDS3231
5,50 €
    DS3231 is a low-cost, extremely accurate I2C real-time clock (RTC), with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. Compared to the DS1302 solution, the DS3231 has many advantages, it function with a VCC ranging from 2.3V to 5.5V and has a battery backup. Unlike the DS1307, the DS3231 also has an integrated crystal...
 2
Available
Electronique

GY-9250 MPU9250 9DOF Accéléromètre Gyro 9 Axis...

SENTAOGY9250
8,25 €
The MPU-9250 is a 9-axis MotionTracking device that combines a 3-axis gyroscope, 3-axis accelerometer, 3-axis magnetometer and a Digital Motion Processor™ (DMP) all in a small 3x3x1mm package available as a pin-compatible upgrade from the MPU-6515. With its dedicated I2C sensor bus, the MPU-9250 directly provides complete 9-axis MotionFusion™ output. The...
 2
Out of stock
Senseurs

Grove-Q Touch Sensor

GROSEETOUSEN
18,69 €
The Q Touch Sensor is a high sensitivity and high noise immunity touch input device
 2
Product available with different options
Electronique

RGB and Gesture Sensor Module APDS-9960

SENSPAAPDS9960
15,00 €
Touchless gestures are the new frontier in the world of human-machine interfaces. By swiping your hand over a sensor, you can control a computer, microcontroller, robot, etc. One manufacturer has even created a touchless toilet that flushes when you move your hand over the tank. The Avago APDS-9960 offers ambient light and color (as clear, red, green, and...
 2
Available
Senseurs

Mini PIR Motion Sensor Module

SENJANMPIR
4,00 €
Small and exquisite appearance, it is convenient to carry. Full-automatic induction, excellent sensitivity. One kind of trigger modes, it is easy to operate. Stable reliability, ultra low voltage operating mode. It can be widely used in many kinds of automatic induction electric equipment. Suitable for movement detection, automatic control, proximity...
 2
Available
Electronique

TP101 Electronic Digital Thermometer

THEELCTP101
3,67 €
Flexible change between℃ and ℉. Made in pen-type structure for convenient use. Made of stainless steel probe which is safer and more durable. Shares High accuracy with 0.1℃ resolution. Shares LCD display for wider measuring range and high stability. With Power saving mode which could shut-down automatically after 10 minutes. Shares various measured...
Available
Electronique

Piezo Ceramic Transducteur 12MM

SENFLYPIEZOD12
1,67 €
Simply supply it with 5V power (or less than 25V), it will start vibrating, use another analog signal to control the power via Arduino.
 2
Available
Electronique

GY-BME280 High Precision Atmospheric Pressure,...

SENGYBME280
10,08 €
GY-BME280 is a Breakout Board featuring a Bosch Sensortec BME280 Temperature, Humidity & Pressure Sensor. The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm. Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k,...
 2
Available
Electronique

Soil moisture sensor

SENGENMOIST
2,00 €
Soil moisture module is most sensitive to the ambient, generally used to detect the moisture content of the soil.When the module can not reach the threshold value, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low;The small board digital output D0 can be connected directly to the MCU, MCU to detect...
 2
Available
Electronique

Resistive Strain Foil Jauge de déformation,...

SENELDSTRAIN
4,92 €
sont idéales pour les mesures de déformation dans les autoclaves ou en présence de vapeur The resistive foil sensor that is used to measure the strain that occurs on an object. The strain sensor foil can be easily attached to any object by just sticking to the object.
 2
Available
Senseurs

Capteur de niveau d'eau (Water Level Sensor)

SENFLYWTR
1,25 €
This is simple and small portable water level/water droplet identification, detection sensor water that have high cost performance. Complete water yield and analog conversion, the output value apply to your custom function. It is low power consumption and high sensitivity. It can make better performance with Arduino 328 controller and sensor relay...
Available
Accueil

Thermocouple Temperature Sensor K-type (Spring...

SENTMPTERCP
5,00 €
K-type thermocouple, its temperature resolution capability is 0. 25 Degree, cold junction compensation range - 20 ~ + 80 Degree, wide operating voltage range 3. 0 ~ 5. 5V. Internal integrated cold with compensation circuit.
  • Prix réduit / -1,00 €
Available
Electronique

Module capteur de flamme (Arduino Compatible)

MODSENFLAMETEMP
2,50 € 3,50 €
Flame Sensor Moduthermole IR Sensor Detector Smartsense For Temperature Detecting Suitable For Arduino
Out of stock
Electronique

Electronic Brick - Sound Sensor/Microphone Brick

SENITESNDMIC
2,50 €
Electronic brick of microphone can be connected to the analog I / O port, when speaking to the microphone, the analog value will be changed. A recorder can be made by reading and saving the analog value.
 2
  • Prix réduit / -2,00 €
Available
Senseurs

DHT-22 Temperature & Humidity Sensor

SENDHT22
6,25 € 8,25 €
The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The sensor is calibrated and doesn't require extra components so you can get right to measuring relative humidity and temperature.
 2
Available
Senseurs

Grove - Barometer Sensor (BMP085)

BARSEEGROVBAROM
14,17 €
This Grove-Barometer Sensor features a Bosch BMP085 high-accuracy chip to detect barometric pressure and temperature. It can widely measure pressure ranging from 300hPa to 1100hPa, AKA +9000m to -500m above sea level, with a super high accuracy of 0.03hPa(0.25m) in ultra-high resolution mode.
 2
Available
Senseurs

GP2Y1010AU0F Compact Optical Dust Sensor

SENDUSTGP2Y1010AU
11,67 €
The Sharp Optical Dust Sensor (GP2Y1010AU0F) is especially effective in detecting very fine particles like cigarette smoke, and is commonly used in air purifier systems.
 2
  • Prix réduit / -4,00 €
Available
Senseurs

DSM501A dust sensor

SENDUSDSM501A
14,00 € 18,00 €
The dust sensor module DSM501A is low cost,compact size for a particle density sensor.
 2
  • Prix réduit / -6,67 €
Available
Accueil

Module senseur UV (UVM30A)

ECRSEUV30M
15,00 € 21,67 €
The UV Sensor is used for detecting the intensity of incident ultraviolet(UV) radiation. This form of electromagnetic radiation has shorter wavelengths than visible radiation. This module is based on the sensor UVM-30A, which has a wide spectral range of 200nm-370nm. The module outputs electrical signal which varies with the UV intensity, which gives your...
 2
Available
Electronique

Module optique opto capteur mesure de vitesse...

ECRSPS04022S
1,88 €
This Opto interruptor detects if there is some thing between the IR emitter and the IR receiver. With the Holder, it will be very easy to intall this sensor into your application.
Available
Electronique

Reed Switch

ECRSPM02102S
0,92 €
The reed switch is an electrical switch operated by an applied magnetic field. When the device is exposed to a magnetic field, the two ferrous materials inside the switch pull together and the switch closes. When the magnetic field is removed, the reeds separate and the switch opens. This makes for a great non-contact switch. It consists of a pair of...
 2
Available
Accueil

Flame Sensor

ECRSPM21020F
1,17 €
Simple flame sensor
 2
Available
Electronique

DHT-11 Temperature & Humidity Sensor

SENDHT11
2,50 €
This sensor provides temperature and humidity data with a quite good sensibility in a serial format thanks to its built-in micro-controller.
 2
Available
Senseurs

BMP085 Digital Pressure Sensor Module (GY-65)

SENSEDBMP085
7,92 €
BMP085 is a digital pressure sensor. Its absolute accuracy can reach 0.03hPa and power consumption is extremely low with current of only 1μA when operating in standard mode.
 2
Available
Electronique

IIC EEPROM and RTC Module DS1307 atmel832

iTeadStudio
SENSEDIICRTCEEPROM
4,38 €
With compact design, the board can integrate the real-time clock module DS1307, EEPROM memory AT24C32 and digital temperature sensor DS18B20 (not supplied on the board) which are connected via I2C bus together on a 27mm*28mm*8.4mm board.
  • Prix réduit / -11,00 €
Available
Electronique

Détecteur de mouvements sans-fil 433Mhz PIR...

SENWIRPIR
5,58 € 16,58 €
This is a wireless PIR for your home automation project. With its included batteries, just install it on your wall and voilà, a new door motion sensor !
Available
Electronique

TCRT5000 Photo Interrupter

SENTCRT500
1,50 €
Photo-interrupter to sense when an object is close (if read as digital), and how close it is (if read as analog), in very near range.
  • Prix réduit / -1,00 €
Available
Electronique

DS18B20+

ELCDS18B20
3,00 € 4,00 €
The DS18B20+ is a programmable resolution 1-wire digital thermometer in 3 pin TO-92 package. This digital thermometer provides 9bit to 12bit celsius temperature measurements and has an alarm function with non-volatile user programmable upper and lower trigger points. The DS18B20 communicates over a 1-wire bus that by definition requires only one data line...
Available
Electronique

Digital DS18B20 temperature sensor with steel...

SENDS18B20METAL
6,00 €
This is a digital temperature sensor, that is already calibrated. The measurement is done where the sensor is, no need for long insulated wire or complicated ADC design. This sensor is therefore also perfect for use with a Raspberry Pi, as it is not analogic, all the data is transmitted in digital One Wire protocol.
 2
Available
Electronique

Senseur de courant alternatif non invasif...

SENITECURSCT019
18,00 €
Ce senseur de courant est idéal pour surveiller l'état de votre consommation électrique, en faire des statistiques ou simplement y réagir.
 2
Available
Electronique

Senseur de courant alternatif non invasif...

SENITECURSCT013
13,00 €
Ce senseur de courant est idéal pour surveiller l'état de votre consommation électrique, en faire des statistiques ou simplement y réagir.
 2
Available
Electronique

Module PIR de détection de mouvement et de...

SENITEPIR
6,00 €
Module de détection de mouvement fortement intégré et fréquement utilisé pour détecter les entrées et la présence dans une pièce. Il peut ête utilisé avec n'importe quel micro controlleur, en incluant les arduino, msp430, stm32 ou autres stellaris.
  • Prix réduit / -0,80 €
Available
Electronique

LDR Photo-resistor

SENRSLDR
0,70 € 1,50 €
Basic photo-resistor.
Available
Electronique

Magnetic Door Switch

SWISESDOOR
3,00 €
Senses when a door or window is open or closed... Perfect for use with your favourite micro controller board (be it arduino, launchpad, stm3é or whatever) !
Product added to wishlist
Product added to compare.