Your cart
Il n'y a plus d'articles dans votre panier
Driver de moteur avec dissipateur thermique DRV8825 (utile pour imprimantes 3d, reprap, cnc, etc.)
MDRDRV8825
6,25 €
This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key
Features:
- Suitable for 8.2V~45V (between VMOT and GND for motor), and less than 2.2A (2A for A4988) steppers
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step (1/16 max for A4988)
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45 V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3 V and 5 V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
- Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects.
This product ships with all surface-mount components—including the DRV8825 driver IC—installed as shown in the product picture.
Extra Info:
- Reprap wiki page info.
- In the wiring page, connect blue line to digital pins, red and black lines to power pins VCC and GND, grey pins can leave it to float,
- Search via google to find more use guide
Setup the mode
MODE0 | MODE1 | MODE2 | Microstep Resolution |
---|---|---|---|
Low | Low | Low | Full step |
High | Low | Low | Half step |
Low | High | Low | 1/4 step |
High | High | Low | 1/8 step |
Low | Low | High | 1/16 step |
High | Low | High | 1/32 step |
Low | High | High | 1/32 step |
High | High | High | 1/32 step |
5 Produits
Nouveau produit
No reviews
Les clients qui ont acheté ce produit ont également acheté...
Electronique
IIC EEPROM and RTC Module DS1307 atmel832
SENSEDIICRTCEEPROM
4,38 €
With compact design, the board can integrate the real-time clock module DS1307, EEPROM memory AT24C32 and digital temperature sensor DS18B20 (not supplied on the board) which are connected via I2C bus together on a 27mm*28mm*8.4mm board.
Electronique
Digital DS18B20 temperature sensor with steel...
SENDS18B20METAL
6,00 €
This is a digital temperature sensor, that is already calibrated. The measurement is done where the sensor is, no need for long insulated wire or complicated ADC design.
This sensor is therefore also perfect for use with a Raspberry Pi, as it is not analogic, all the data is transmitted in digital One Wire protocol.
Modules d'Alimentation
DC 5V 2A Micro USB Power supply
ENEADA5V2AMICUSB
8,00 €
This small yet powerful 5V DC 2A USB power module provides all your micro USB projects an easy to use power supply.
Puissance et Energie
LD1117 / LM1117 - 5V LDO Voltage regulator 1.3A...
ELCREG5V1117TO220
1,50 €
This is a simple to use voltage régulator that outputs 5V at 1.3A
Electronique
Adjustable Infrared Sensor Switch 3 - 50cm...
ECRSOD00350S
7,50 €
This is an infrared distance switch. It has an adjustable detection ranging from 3cm to 50cm.
Outils de dev.
PL2303 USB to UART (TTL) breakout
USBITEPL23035V
4,08 €
It's a small USB to TTL serial tool, using the PL2303 chip.
You can use it to connect some serial device to your PC via USB port, an avr, an msp430 or an stm32 for example.
It's very cheap compared to the ft232 alternative and works very well, up to more than 1mbit/s.
Outils de dev.
Arduino Mini 05 (light / without headers)...
MCBARDMINI05LIGHT
15,50 €
The Arduino Mini is a small microcontroller board originally based on the ATmega168, but now supplied with the 328.(datasheet), intended for use on breadboards and when space is at a premium. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 8 analog inputs, and a 16 MHz crystal oscillator. It can be programmed with the USB...
Puissance et Energie
Energy Meter HLW8012 Breakout Board 20A
SENELEMETER
3,00 €
Energy Meter HLW8012 Breakout Board 20A