Your cart
Il n'y a plus d'articles dans votre panier
AC-DC 5V 2A 10W Power Module
ENEADA5V2AMOD
6,25 €
This small yet powerful 5V DC 2A power module provides all your projects an easy to use power supply.
Description
This power supply is fully isolated industrial internal power module with temperature protection, overcurrent protection and short circuit full protection, AC85 ~ 265V wide voltage input, high and low voltage isolation, DC12V1A output voltage, 431 regulated output with EMI filter circuit, with status LED, with installation holes, cost-effective.
Features:
- Input (full load): AC 85-265V or DC 100v-370v
- Input current (full load): 0.027(AC110V) 0.0136(AC220V)
- Input inrush current (full load): 20A
- Output: 5V, 0-2A, 2.2A max, output voltage range 4.8-5.2V, 60mV voltage wave
- DC output power: 10W
- Efficiency: 80%
- On/off overload range: 10%
- Output upward time: 100ms
- Size: 6.6*3.0*2.1 CM
- Pin Definition one side marked AC N, AC L, and another side is 5V, gnd.
- On board status LED
Protection: overload, short circuit, overheat, over-current protection. Board will lock and recover when turn it on/off.
Reliability: Environment 25 ℃, at 80% load MTBF more than 16,000 hours
1 Article
Nouveau produit
No reviews
Les clients qui ont acheté ce produit ont également acheté...
Connectivité sans fil
ESP-01S WiFi Serial Transceiver Module with...
SEDWIFSERTRNESP
4,58 €
This is the pin compatible upgrded version of the ESP-01 chip.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has...
Outils
Q Oil Q30 Super film protecteur en aerosol...
TOLSPRAQ30
16,67 €
Q Oil Q30 Protective Removable Film Spray
Outils de dev.
PRO MICRO 5V/16MHZ Micro USB Leonardo
PROMICRO5V
8,25 €
The Pro Micro is an Arduino compatible microcontroller development board based on the ATmega32U4 IC designed by Sparkfun Electronics. It is based around the Arduino Leonardo which means you no longer need an addition USB-Serial Interface to program your Arduino.
Puissance et Energie
DC 12V 15A Power supply JC-12V-15A
ENEADA12V15AS
24,17 €
12V DC 15A power module 220V
Bases de l'électronique
Module de relais deux canaux (5V, 250VAC)
RELITD2CH5V
5,08 €
7,08 €
Ceci est un module de relais à 2 canaux avec un contrôle à 5VDC. Il peut être connecté directement à une grande gamme de microcontrolleurs comme les Arduino, AVR, PIC, ARM, MSP430, STM32, etc.
Raspberry Pi
Raspberry Pi 4 Modèle B 2 Go
LINRPI4B2GB
65,00 €
Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor speed, multimedia performance, memory, and connectivity compared to the prior-generation Raspberry Pi 3 Model B+, while retaining backwards compatibility and similar power consumption. For the end user, Raspberry Pi...
Electronique
Infrared Kit - IR Receiver (HS0038) + IR LED...
IRELDRECTRANS
0,79 €
IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.
Puissance et Energie
dc-dc input 12V / output 5V and 3.3V 6A (stepdown)
ENETAO12V335
6,00 €
DC-DC input 12V / output 5V and 3.3V 6A Modul
Electronique
Dual female splittable jumper wires (100mm, 40...
CONSEDJMP40PFF10
3,33 €
This is a splittable 40 pin dual female jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.