Your cart
Il n'y a plus d'articles dans votre panier
2.4G CC2530 Module (Zigbee compatible)
WIRELDCC2530
13,67 €
Easy efficient network module. (1 item only, you will need to buy 2 if you want a pair)
Features:
- support Point-to-Point mode or boardcast mode
- 0% data lost on Point to point mode, only one point to one point,
- 1% data lost on boardcase mode, all points to all points
- send and receive in the mean time, no packet length limit, full-duplex
- wide range of voltage auto support, 3~5.5V
- operational current 30mA
- 4.5dBM operational power
- USB TTL 3.3-5.5V auto supported
- easy config: button press config
- open area transmission distance 250 meters
- on board PCB antenna
- 16*32mm, wireless 2.4 – 2.45 G
- Transmission rate 3300 Bps, baudrate support: 115200, 57600, 38400, 19200,14400, 9600, 4800. 2400
- Serial USB-TTL interface
Config Steps
two red LED on top, two green LED on bottom
Step | Action (short press) | Indication | Next(long press and release) | note |
---|---|---|---|---|
1. Enter into config | HOLD button and power up | all leds blink in turn | enter into next config | -- |
2. Config baudrate | switch baudrate | see image below | enter into next config | -- |
3. Set wireless channel | choose channel | Led indicate 16 channels, including all leds off status | enter into next config | if the channel is same, the module can communicate even baudrate is different |
Mode set | switch in the three modes | see image below | enter into next config | -- |
5. Confirm | -- | long press until LED blink in turns, and release LED will remain for 2 secs and done | -- | -- |

2 Produits
Nouveau produit
No reviews
Les clients qui ont acheté ce produit ont également acheté...
Electronique
0.1" (2.54mm) Female header 1 row / 40 pins
CONGENFEM40
0,92 €
This is a simple female header, very useful for a lot of things, including to plug boards like the stm32f4 discovery or the arduino nano on your protoboards.
Prototypage
Solderable Mini Breadboard PCB (protoboard)
BRBEDRSOLDPCB
1,50 €
Layout same as mini breadboard, and also same connection in the veritcal pin line.
Electronique
Batterie Lithium polymer - 3.7V 2500 mAh
ENEBATLP475085
15,00 €
C'est une batterie légère mais de haute densité, basée sur la technologie Lithium Ion Polymer (plus robuste et sécurisée que les batteries li-poly). Cette batterie qui sort un voltage nominal de 3.7v à 2500mAh possède un connecteur standard JST 2-pin (2.54mm d'espacement).
Raspberry Pi
RaspberryPi 3 Modèle B (Raspberry Pi, Quad-core...
LINRPI3B
La carte Raspberry Pi 3, modèle B, ressemble à première vue à la carte Pi 2 B. Sa taille est identique et elle reprend .
Connecteurs et Fils
USB to TTL (UART) Cable
CONCBBUSBTTLCAB
8,25 €
USB to TTL Cable, specialized for dev boards.
5V
Electronique
Dual female splittable jumper wires (300mm, 40...
CONSEDJMP40PFF
3,00 €
5,00 €
This is a splittable 40 pin dual female jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Electronique
Module de relais 8 canaux (5V, 250VAC)
RELITD8CH5V
16,00 €
Ceci est un module de relais à 8 canaux avec un contrôle à 5VDC. Il peut être connecté directement à une grande gamme de microcontrolleurs comme les Arduino, AVR, PIC, ARM, MSP430, STM32, etc.
Puissance et Energie
dc-dc input 12V / output 5V and 3.3V 6A (stepdown)
ENETAO12V335
6,00 €
DC-DC input 12V / output 5V and 3.3V 6A Modul
Son
Module d'amplification audio mono LM386 (Audio...
SNDGENAMPLILM386
3,17 €
LM386 Audio Amplifier Module 20 Times 5V-12V 8 - 32 Ohms / Input 10K Adjustable Resistance.
Affichage
20x4 Characters LCD (White on Blue) (screen 20.04)
LCD2004WB
9,00 €
This cheap 20x4 characters lcd is perfect for use with an arduino or any other microcontroller to display data quickly. It is compatible with the Hitachi HD44780 lcd driver.