2.2" Serial TFT LCD Display (SPI, 176X220, ILI9225) (screen)
LCDGEN22ILI9341
10,00 €
12,50 €
-2,50 €
This great little display boasting a 176X220 resolution has a wide support for all your MCU and little ARM/Linux-based boards. It will work on Arduino, STM32, Raspberry Pi and others.
Oh, did I mention it also has an SD card slot ? Making it maybe one of the best value display we can have to offer.
Feature:
- TFT01_2.2 SP is a 2.2 "SPI TFT LCD Screen Module, 10pins interface, compatible 5110 LCD interface. Not just a LCD break but include SD card (2GB),
- The LCD in the TFT01 is ILI9225. It's a 176X220 (resolution), 2.2S inch TFT LCD screen.The LCD has a wide viewing angle, the contrast is also very suitable.
- The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
- Replace LCD5110 and is compatible with all the shields having a slot for it.
- SDcard uses hardware SPI interface (CS / MOSI / MISO / SCK) (those pins come unsoldered for compatibility with other displays)
Parameter:
- SDO: Serial clock output
- LED: 3.3V IO and Power Supply pin
- SCL: Serial clock input
- SDA / SDI: Serial data input
- DC: Data / Command selection
- RST: Reset, Low level active
- CS: Chip Selection, Low level active
- GND: Ground
- VDD33: 3.3V Power Supply pin
- UTFT Support
Dimensions
Usage
On Arduino just use the UTFT library, it has a built-in model for the 2.2" ILI9341 displays.
On Raspberry PI and other linux boards, the FBTFT has a mode for it. There is a tutorial here. TL;DR :
- Install the FBTFT kernel module following this tutorial
- Wire the SPI MOSI/SCK/SS(CS) wires to the equivalent on the Raspberry PI.
- Wire the Reset, D/C and LED to the GPIO you want, but remember their number.
- Install the module with (replace the GPIOs with what you have chosen):
sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:25,dc:24,led:18 speed=16000000 rotate=90 bgr=1 - Now you can activate it :
con2fbmap 1 1
On STM32 boards, there is native support for it as the STM32F429 Discovery board includes one. Here is a library/tutorial for ILI9341 displays.
6 Produits
Nouveau produit
No reviews
Les clients qui ont acheté ce produit ont également acheté...
Electronique
4x6 Protoboard
PCBPROTO4x6
1,50 €
no odor
finely drilled
tough
including power pad.
Clean hole
Raspberry Pi
RaspberryPi 3 Modèle B (Raspberry Pi, Quad-core...
LINRPI3B
La carte Raspberry Pi 3, modèle B, ressemble à première vue à la carte Pi 2 B. Sa taille est identique et elle reprend .
Electronique
USB Cable Type A to 5.5mm Barrel Jack Adapter
CONGENUSBBARREL
4,00 €
This is a simple adapter from an usb port to a barrel jack connector, very useful for Arduino and other mcu board with a barrel jack adapter.
Accueil
Grove - Mega Shield
SEDGROMEGASHI
10,00 €
Mega Shield is a extension board for Arduino Mega, DUE and Google ADK.
Electronique
433Mhz spring cooper antenna
WIR433ANT
1,67 €
This is a dedicated antenna which is especially designed for a wireless communication system (433MHz). It has good VSWR, small size, ingenious structure, easy installation, stable performance, with good anti-vibration and anti-aging ability.
Electronique
Digital DS18B20 temperature sensor with steel...
SENDS18B20METAL
6,00 €
This is a digital temperature sensor, that is already calibrated. The measurement is done where the sensor is, no need for long insulated wire or complicated ADC design.
This sensor is therefore also perfect for use with a Raspberry Pi, as it is not analogic, all the data is transmitted in digital One Wire protocol.
Electronique
74HC595 Shift-Register (DIP)
ELC74HC595
1,20 €
The very popular 595 shift register chip of the 74 series is used a lot by hobbyis because of its wide availability, good speed and simplicity. Just plug it on an arduino like shown in the tutorials and youi have 8 more outputs, put two and you have 16 more outputs ! (up to a lot of them actually, with only three pins !)
Outils de dev.
Arduino-Compatible Pro Mini [16M/5V, 8M/3V3]
MCBARDPROMIN
5,42 €
The minimal design approach to EDArduino, and fully compatible with arduino. This is a 5V EDArduino running the 16MHz bootloader (select ‘Arduino pro mini′ within the Arduino software). EDArduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need.
We recommend first time EDArduino...
Outils de dev.
AD9850 0-40MHz DDS Module
ADITAD9850
10,83 €
IC AD9850 is an ADI DDS chip which be common used in many DDS projects. This AD9850 DDS module is basic on this ADI AD9850 chip. This module provide you a ready made hardware and you can use serial or parallel pins on board to control the AD9850 for different frequency out put. The duty can be adjust by a adjustable resistor - which change the adjust...