Your cart
Il n'y a plus d'articles dans votre panier
Active Speaker Buzzer Module 5V (Arduino Compatible)
MODBUZZ5V
1,50 €
Active Buzzer is an integrated structure electronic transducers, DC voltage supply, widely used in computers, printers, copiers,
alarms, electronic toys, automotive electronic equipment, telephones, timers and other electronic products for sound device.
Piezo buzzer divided into electromagnetic buzzer and buzzer.
The buzzer in the circuit use the letter "H" or "HA" ( old standard with "FM", "LB", "JD" , etc.) indicates.
Buzzer mainly by multivibrator, piezo buzzer , impedance matching and resonance box , casing and other components.
Some buzzer case is equipped with light-emitting diodes.
Multivibrator constituted by the transistors or integrated circuits . When switched on (1.5 ~ 15V DC working voltage ) , multi-harmonic oscillator start-up , the output 1.5 ~ 2.5kHZ audio signals , impedance matching push piezo buzzer sound.
Electromagnetic buzzer from the oscillator, the electromagnetic coils, magnets, and other components diaphragm and the housing
After power on, the audio signal generated by the oscillator current through the electromagnetic coil , the electromagnetic
coil generates a magnetic field .
The electromagnetic coil and the diaphragm is the interaction of the magnet, periodically
vibrating sound.
Buzzer mainly by multivibrator, piezo buzzer , impedance matching and resonance box , casing and other components.
Some buzzer case is equipped with light-emitting diodes.
Multivibrator constituted by the transistors or integrated circuits . When switched on (1.5 ~ 15V DC working voltage ) , multi-harmonic oscillator start-up , the output 1.5 ~ 2.5kHZ audio signals , impedance matching push piezo buzzer sound.
Electromagnetic buzzer from the oscillator, the electromagnetic coils, magnets, and other components diaphragm and the housing
After power on, the audio signal generated by the oscillator current through the electromagnetic coil , the electromagnetic
coil generates a magnetic field .
The electromagnetic coil and the diaphragm is the interaction of the magnet, periodically
vibrating sound.
6 Produits
Nouveau produit
No reviews
Les clients qui ont acheté ce produit ont également acheté...
Electronique
Dual female splittable jumper wires (200mm, 40...
CONSEDUALFP40P20
4,17 €
This is a splittable 40 pin jumper wire, it is super flexible, can be transformed from 1-40 pin jumper wire. With some of these, you will no need to worry about the jumper wires you got before do not fit your project, just split it and go.
Electronique
Boîtier 9V 6F22,6LR61 fils 150mm (Holder 9V)
CONHOLD9VW
2,67 €
This is a simple adapter from 9v batteries very useful for Arduino and other mcu board
Electronique
3 Axis Compass GY-271 (HMC5883L breakout) (sensor)
SENCOMPGY271
4,58 €
This 3 Axis Compass boad has a very good sensibility and features all the needed components to use the excellent HMC5883L chip
Electronique
Commutateur tactile (bouton poussoir) 6x6x4mm
SWIRSCFSM2JH
0,50 €
C'est un simple bouton poussoir (commutateur tactile) de 6x6mm, parfait pour installation sur une platine de prototypage ou circuit traversant.
Electronique
TCRT5000 Photo Interrupter
SENTCRT500
1,50 €
Photo-interrupter to sense when an object is close (if read as digital), and how close it is (if read as analog), in very near range.
Electronique
Micro SD Card Reader Module - SPI interfaces...
MODJANMCSDCTF
2,42 €
Support Micro SD card(<=2G), micro SDHC card(<=32G)Interface level: 5V or 3.3VPowr supply: 4.5V to 5.5V , 3.3V voltage regulator circuit boardCurrency: 0.2-200mACommunication interface: SPIWith 4 holes for M2 screw. Easy to install
Electronique
Jack 3,5mm (Female ST, with grommet straight...
CONBARJACKJC121
1,58 €
Jack 3,5mm; female; st, with grommet; straight; for cable
Outils de dev.
ATMega 328 with Arduino UNO R3 bootloader...
ELCARDUNOATM328
4,67 €
ATMega328 32K microcontroller with pre-loaded Arduino UNO bootloader
Outils de dev.
nRF24L01+ with PA and LNA 2.4Ghz RF module...
WIRITENRF24L01PALNA
6,50 €
12,00 €
This is a long distance 2.4G wireless module which basic on nRF24L01+ chip, and there is the PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.