Base Shield V2

Marque: Seeed Studio

Référence ASHSESBASE

8,00 €

As an expansion board, Base Shield v2 has many Grove connectors, making it convenient for you to use Grove products together. And It is compatible with a series of Arduino products.

Nos engagements

Tous nos produits sont livrés depuis Paris.
Un doute sur votre achat ? Retournez-nous le produit sous 7 jours et nous vous remboursons.
Nous choisissons et testons minutieusement les produits que nous vendons pour vous proposer uniquement le meilleur.

Features

Power Compatible: Every Grove connector has four wires, one of which is Vcc. However, not every micro-controller main board needs a supply voltage of 5V, some need 3.3V. That's why we add a power switch to Base Shield v2. In this way, you can adjust the voltage of Vcc via this switch, making sure the voltage of Vcc is the same as supply power of the main board.

So While using Arduino UNO with Base Shield v2, please turn the switch to 5v position; While using Seeeduino Arch with Base Shield v2, please turn the switch to 3.3v.

Board Compatible: The number of pinout is the same as that of Arduino UNO R3.

Added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. ---- According to Arduino UNO.

Attention: If using Base Shield v2 with Seeeduino V3, please solder the pads, P1 and P2.

For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

Documents

Please visit our wiki page for more info about this product. It will be appreciated if you can help us improve the documents, add more demo code or tutorials. For technical support, please post your questions to ourforum.

En stock 8 Produits

État Nouveau produit

No reviews

Les clients qui ont acheté ce produit ont également acheté...

Available

Electronique

Light 9g Micro Servo (RC plane helicopter Boat,...

SVO9G

5,75 €

SG90 9g servo is a high quality,low-cost servo for all your mechatronic needs.

Available

Electronique

TCRT5000 Photo Interrupter

SENTCRT500

1,50 €

Photo-interrupter to sense when an object is close (if read as digital), and how close it is (if read as analog), in very near range.

Available

Prototypage

0.1" (2.54mm) Long male header 1 row / 40 pins...

CONPINHDLNG

0,67 €

This is a long male header, very useful for a lot of things, including to plug boards like the arduino on your protoboards.

Available

Connectivité sans fil

ESP-01S WiFi Serial Transceiver Module with...

SEDWIFSERTRNESP

4,58 €

This is the pin compatible upgrded version of the ESP-01 chip. ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP8266 has...

Available

Prototypage

1 Mini Breadboard (Various colors, 4.5x3.5)

PCB00003

2,92 €

Mini size breadboard, perfect to embed in very small prototypes or to put on an arduino shield.

Available

Electronique

Electronic Brick & Grove - Tilt Sensor/Switch...

SENITETILT

2,50 €

Electronic brick of tilt switch can be connected to analog I/O port and used in tilt sensor for smart car or robot. When the sensor is in the horizontal position, the output is high level; when the sensor rotates counterclockwise to form an angle of more than 15 ° with the horizontal line, the output is low level.

Available

Accueil

Dual stepper motor shield

ASHITEDUASTE

11,58 €

Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine.

Available

Puissance et Energie

Lipo Charger Pro (Lipo Rider Pro compatible 1A...

ECRPSB01012B

12,92 €

The LiPo Charger is extremely affordable and easy to use. No programming is required. Plug it in and it works. The internal charger IC handles all the power flow between the various components.