IE Shield (Ethernet ENC28J60 and SD Card) for Arduino (Arduino Compatible)

aucun
IE shield is a Ethernet shield which use the ENC28J60 chip for Arduino. It integrates one Micro-SD card slot and provides main interface breakout. You can use it with Arduino to build your Ethernet development platform.
En rupture de stock
SKU
ASHITEIESHIELD
30,00 € 25,00 €

Tous nos produits sont livrés depuis Paris.

Un doute sur votre achat ? Retournez-nous le produit sous 7 jours et nous vous remboursons.

Nous choisissons et testons minutieusement les produits que nous vendons pour vous proposer uniquement le meilleur.

On connait nos produits, donc si vous avez une question n'hésitez-pas !
Appelez-nous au +33 (0) 1 43 73 15 54 ou au +33 (0) 1 46 59 17 37

IE shield is an Ethernet Shield instantly enables internet connectivity for Arduino projects with ethernet controller ENC28J60.  Just stack it onto an Arduino to create your own networked devices. Easily check connection status with on board indicator lights. Extend your design further with many Electronic / Sensor  brick interface and an TF card socket.

This Ethernet shield support the POE function, you can use use the twisted-pair to power it and the Arduino board below, instead using the USB prower or external power jack supply. If your router or moden don't support POE, then you can use the injector cable to mix the signale and power for POE supply.

Features

  • IEEE 802.3 compatible
  • Supports POE*
  • Integrated MAC and 10BASE-T PHY
  • Receiver and collision squelch circuit
  • Supports one 10BASE-T port with automatic polarity detection and correction
  • Supports Full and Half-Duplex modes
  • Programmable automatic retransmit on collision
  • Programmable padding and CRC generation
  • Programmable automatic rejection of erroneous packets
  • Two programmable LED outputs for LINK, TX, RX, collision and full/half-duplex status
  • Supports Micro-SD card with SPI operation
  • Much analog and digital interfaces breakout include AD/DA/PWM/UART/IIC/GPIO

Hardware

IE sheild

Interface

Pin

Description

UART

1

5V supply.

2

Ground

3

Tx

4

Rx

GPI

1

5V supply.

2

Digital input pin

3

Ground

GPO

1

5V supply.

2

Digital output pin

3

Ground

DA

1

5V supply.

2

Analog output pin

3

Ground

PWM

1

5V supply.

2

PWM output pin

3

Ground

AD0/1/2

1

5V supply.

2

Analog input pin

3

Ground

IIC

1

5V supply.

2

Ground

3

Data wire of IIC

4

Clock wire of IIC

Ethernet module SPI

1

5V supply.

2

Ground

3

Chip select pin(Low active)

4

Chip reset pin(Low active)

5

Chip data input pin

6

Chip clock input pin

7

Weak on Line output pin(Low active)

8

Chip data output pin

9

Chip programmable clock output pin

10

Interrupt output pin(Low active)

Downloads

Plus d’information
Compatibilité avec les cartes Arduino clones, Arduino Due, Arduino Duemilanove, Arduino Leonardo, Arduino mega, Arduino Pro, Arduino Uno, iTeaduino mega, Seeeduino mega
Fabricant Non
Couleur Non
Voltage 3.3v, 5.5v
Connectivité Non
Package Non
Mémoire Flash (programme) Non
Tension en entrée Non
Fréquence Radio Non
Rédigez votre propre commentaire
Vous commentez :IE Shield (Ethernet ENC28J60 and SD Card) for Arduino (Arduino Compatible)
Votre évaluation