Drivers électroniques (de moteurs, etc.)

 2
Available
Motorisé

BTS7960 Module High Power Smart Car Motor Drive...

MDRTAOBTS7960
14,00 €
Double BTS7960 large current (43 A) H bridge driver; 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board; voltage indication of motor driver output end; can solder heat sink;
 2
Available
Arduino

CNC Shield for Arduino (GRBL Arduino Compatible)

ASHCNCGRBLKIT
6,67 €
The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepper motors using 4x A4988 or DRV8825 with this shield and an Arduino you can build all kinds of robotics or CNC projects including CNC routers, laser cutters and even pick&place machines. This is the KIT...
Available
Arduino

CNC Shield pour NANO V3 Arduino (Arduino...

ASHCNCNANOKIT
6,67 €
The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepper motors using 4x A4988 or DRV8825 with this shield and an Arduino you can build all kinds of robotics or CNC projects including CNC routers, laser cutters and even pick&place machines. This is the KIT...
Available
Electronique

Driver de moteur avec dissipateur thermique...

MDRA4988
6,25 €
The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase...
 2
Available
Electronique

Driver de moteur avec dissipateur thermique...

MDRDRV8825
6,25 €
This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for...
 2
Available
Accueil

Dual Motor Driver 1A TB6612FNG

MOTDUALDRIVER
6,80 €
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.
 2
Available
Accueil

Dual stepper motor shield

iTeadStudio
ASHITEDUASTE
11,58 €
Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine.
 2
Available
Electronique

EasyDriver allegro stepper motor driver

MDREASYDRIVER
5,00 €
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and...
 2
  • Prix réduit / -4,17 €
Available
Electronique

L298 Dual H-Bridge Motor Driver

SESMOT103B1M
8,33 € 12,50 €
If you are building a robot with wheels, you need a dual H-Bridge driver like this one. Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive...
Available
Impression 3D

RAMPS 1.4 5x Stepper motor driver mount shield...

ASHRAMPS14
12,50 €
RepRap Arduino Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an...
 2
Available
Impression 3D

RAMPS 1.5 5x Stepper motor driver mount shield...

ASHRAMPS15
12,50 €
RepRap Arduino Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an...
 2
Available
Moteur et servo-moteurs

Raspberry Pi Motor Shield Kit ( Robotique, L293D )

SHDELDPI293
5,50 €
Plug the RaspiRobot Board into the GPIO port on the Raspberry Pi and it provides dual bi-directional motor controllers, two open collector outputs, two switch inputs, a pair of status LEDs and even a voltage regulator capable of powering the Pi using a battery source from 7-12VDC.
 2
Available
Motorisé

Shield Moteur pour Arduino VNH2SP30

ASHSESMOTV2
16,58 €
Description This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm...
 2
Available
Drivers électroniques (de moteurs, etc.)

TB6560 Motor driver (max 3A, 10-35v motor,...

MDRTB65603A
10,00 €
A quite powerful motor driver, taking from 12v to 24v as input. It even has opto-couplers to separate your driving electronics from the motor power.
 2
Available
Motorisé

TB6600 Stepper Motor Driver 4A 9~42V TTL 32...

MDRJANTB6600
12,50 €
TB6600 upgraded version of the stepper motor drive is a professional two-phase stepper motor driver with 8-speed control segment (1,2,4,8,16, 32), 6-speed current control (0.5A, 1A , 1.5A, 2A, 2.5A, 3A, 3.5A, 4A), drive means or without noise, vibration, smooth running characteristics. 9v-42V DC power access.
 2
  • Prix réduit / -2,00 €
Available
Electronique

ULN2003 Stepper Motor Driver Board

iTeadStudio
MDRULN2003
2,58 € 4,58 €
ULN2003 Stepper Motor Driver Board is use the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motors (5v-12v).
Product added to wishlist
Product added to compare.